I'm sorry, I cannot fulfill that request.
Added by David W.
Close
Step 1
Is it due to a lack of capability, resources, or other constraints? Show more…
Show all steps
Your feedback will help us improve your experience
Labs
Want to see this concept in action?
Explore this concept interactively to see how it behaves as you change inputs.
Key Concepts
Recommended Videos
Determining the Heat of Reactions in Aqueous Solutions Make sure you open the virtual lab as titled at the top of this page: Determining the Heat of Reactions In Aqueous Solutions. The stockroom of the virtual laboratory contains a cabinet called "Thermochemistry Solutions." Different concentrations of Reagent A and Reagent B have been placed into this cabinet. You will use these solutions to answer the questions below. For each trial, use 50 mL each of the same concentration of solutions A and B. You will need the coffee cup calorimeter located in Glassware under Other. You will need the 50 mL graduated cylinder and your A and B solutions. Experimental Procedure: 1) Combine 50 mL of 0.10 M A with 50 mL of 0.10 M B in the coffee cup calorimeter. You will need to note the original temperature of the solutions, and the temperature after combining the two solutions and place your data in the table below. 2) Repeat the experiment above using 1.00 M A and 1.00 M B, and then again using 3.00 M A and 3.00 M B.
Supreeta N.
Tetramethylammonium Triiodide 2 mL Erlenmeyer flask; put tetramethylammonium iodide (CH3)NI (0.50 g), and ethyl alcohol (20 mL). Add iodine (0.65 g). Heat in water bath and stir the mixture until all the white solid has dissolved. Allow to cool slowly to room temperature and finally cool on ice. Filter under suction and dry in air. Record the color of the product. Measure melting point. Record the weight obtained and calculate the percentage yield. Analysis: One of the accepted ways for chemists to prove that they have made the compounds they claim is by obtaining satisfactory elemental analyses. This usually means determining the percentage by weight of one or more of the elements present in the compound. In the case of the compound you synthesized, iodine is the easiest element to determine by redox titration. Dissolve sodium bisulfite NaHSO3 (1.04 g, 0.01 mol) in water (100 mL) to get 0.1 M NaHSO3. Fill buret with bisulfite solution. Accurately weigh 0.204 g of [unknown unit] mol?), dissolve in ethanol (10 mL), and titrate with bisulfite solution to get the exact concentration of 0.1 M NaHSO3. Weight accurately about 0.20 g [unknown unit] mol?) of the product in a flask and dissolve in ethanol ([unknown unit] mL). Titrate iodine (from triiodide) with bisulfite solution until colorless. Write and balance the chemical equation. From titration data, calculate the molar amount of iodine in your sample of triiodide. Calculate the percentage purity of your tetramethylammonium triiodide product. b) Tetramethylammonium Pentaiodide: Prepare the compound as described above, using 0.50 g of (CH3) [unknown unit] and 1 g of iodine. Observe the color of the dry product. Measure melting point. Calculate the percentage yield. Titrate iodine (from pentaiodide) with NaHSO3, as described above. Calculate the percentage purity of pentaiodide.
Sri K.
CHM 152 Lab 7: Le Châtelier's Principle Introduction In this lab you will test Le Châtelier's principle on three different chemical equilibria. You will see how adding or removing a component of system results in a shift to the right or left in addition to shifts caused by the addition or removal of heat. From observing the effect of heating and cooling the system, you can determine if a system is exothermic or endothermic. First, you will examine the dissociation of bisulfate (hydrogen sulfate), HSO4⁻, which is a weak acid in water. HSO4⁻(aq) + H2O(l) ⇌ H3O⁺(aq) + SO4²⁻(aq) Since all species in this system are colorless, we will use a pH indicator known as Thymol Blue, which is yellow to orange in low concentrations of hydronium and red in higher concentrations. Next, you'll study the equilibrium of magnesium hydroxide. You'll initially form the compound by reacting sodium hydroxide and magnesium chloride, but the actual system that will be studied is given below. While magnesium hydroxide is consider to be insoluble, an equilibrium does exist between the solid and the small fraction aqueous ions that form in solution. Mg(OH)2(s) ⇌ Mg²⁺(aq) + 2OH⁻(aq) We will observe changes in this system in two ways: through the appearance and disappearance of the solid reactant as well as changes in pH using phenolphthalein as an indicator. With phenolphthalein, as the solution's basicity increases, the solution will turn increasingly pink or magenta. Finally, you'll look at the equilibrium of aqueous tetrachlorocobalt (II) ion, CoCl4⁻, which will be performed in an alcohol solution (as opposed to the aqueous solutions we normally study). CoCl4⁻(alc) + 6H2O(alc) ⇌ Co(H2O)6²⁺(alc) + 4Cl⁻(alc) (alc = alcohol solution) Unlike the previous two systems, we won't need to add an indicator here because the two cobalt species have their own distinct colors: CoCl4⁻ ion is blue while Co(H2O)6²⁺ is pink. Concepts to Review • LeChâtelier's principle • Solubility of ionic compounds • Acid-base (neutralization) reactions
Recommended Textbooks
Chemistry: Structure and Properties
Chemistry The Central Science
Chemistry
Transcript
Watch the video solution with this free unlock.
EMAIL
PASSWORD