solution using assembly language 8085 code asap plzevaluate the circuit schematics in figure 2 a

Here in this question first we have to write down a given data that is the value of alpha that i

This problem will be looking at coding in Arduino. So we're specifically considering LEDs. So if

In this question we have been given the reading or result of two thermal sensor, okay? And we ha

from energy conversation final kinetic energy is equal to initial kinetic energy that is m into

following question it is that RT which is equals to 1670 ohm okay and T which is equals to 100 d

Question

Solution Using Assembly Language 8085 Code... ASAP Please Evaluate the circuit schematics in Figure 2 and write an assembly program for the IR thermometer that measures temperature and displays the temperature value on the 2 seven-segment displays. The thermometer blinks the LED at a 100ms rate for 10 times if the measured temperature is greater than 38 Â°C. Assume that the IR sensor board starts converting the temperature value as soon as the CONVERT* signal is asserted by the processor, and then a valid data will be available at the output port whenever the READY signal is asserted low (active low) by the sensor board. (Hint: Use any delay time to represent 100ms in MySIM85) In order to simulate the system in MySIM85, you need to replace all inputs by switches or buttons. All inputs to the processor are as follows: 1. Ready pin 2. Output pins of IR Sensor board (D0-D7) 8255A 32 31 30 20 00008000 30 38 37 PA7 PBO RD 36 WR 8 A1 9 AO 87 35 RESET 6 Cs VDD - VDD READY CONVERT* VDD RE oa 01 D D3 D4 D5 GND GND R Sensor Board active low LED PPI8255A 8255A1 LED2 FD 8. NC 8. S43018 40 19 38 17 R16 PBO 18 RD 19 PB1 26 WR 20 21 22 A1 PB4 23 40 34 PB7 2 35 RESET PCO CS ETE

          Solution Using Assembly Language 8085 Code... ASAP Please

Evaluate the circuit schematics in Figure 2 and write an assembly program for the IR thermometer that measures temperature and displays the temperature value on the 2 seven-segment displays. The thermometer blinks the LED at a 100ms rate for 10 times if the measured temperature is greater than 38 Â°C. Assume that the IR sensor board starts converting the temperature value as soon as the CONVERT* signal is asserted by the processor, and then a valid data will be available at the output port whenever the READY signal is asserted low (active low) by the sensor board. (Hint: Use any delay time to represent 100ms in MySIM85)

In order to simulate the system in MySIM85, you need to replace all inputs by switches or buttons. All inputs to the processor are as follows:
1. Ready pin
2. Output pins of IR Sensor board (D0-D7)
8255A
32 31 30 20
00008000
30 38 37
PA7 PBO
RD 36 WR 8 A1 9 AO 87 35 RESET 6 Cs
VDD
-
VDD READY CONVERT*
VDD RE
oa 01
D
D3 D4
D5
GND
GND R Sensor Board
active low LED
PPI8255A
8255A1
LED2
FD
8. NC
8. S43018
40 19 38 17
R16
PBO 18 RD 19 PB1 26 WR 20 21 22 A1 PB4 23 40 34 PB7 2  35 RESET PCO CS
ETE

solution using assembly language 8085 code asap plzevaluate the circuit schematics in figure 2 and write an assembly program for the irthermometer that measures temperature and display the t 72522

Added by James E.

Question

Please give Ace some feedback