Question

Use the data in the table below to set up short-run X-bar and R charts using the DNOM approach. The nominal dimensions for each part are T(A) = 151.5, T(B) = 54.0, T(C) = 30.0, T(D) = 100.5, and T(E) = 124.5. Sample Part M1 M2 M3 1 A 154 150 155 2 A 151 152 149 3 A 148 155 152 4 A 152 151 149 5 A 154 154 152 6 A 148 150 151 7 B 56 54 56 8 B 52 55 52 9 B 55 53 55 10 B 53 56 56 11 B 52 54 52 12 B 54 56 54 13 C 28 29 29 14 C 28 32 30 15 C 30 29 32 16 D 100 98 102 17 D 102 101 102 18 D 98 99 100 19 D 102 102 102 20 D 100 98 102 21 E 122 124 125 22 E 122 124 128 23 E 123 128 125 24 E 127 122 123 25 E 126 123 123

          Use the data in the table below to set up short-run X-bar and R charts using the DNOM approach. The nominal dimensions for each part are T(A) = 151.5, T(B) = 54.0, T(C) = 30.0, T(D) = 100.5, and T(E) = 124.5.

Sample	Part	M1	M2	M3
1	A	154	150	155
2	A	151	152	149
3	A	148	155	152
4	A	152	151	149
5	A	154	154	152
6	A	148	150	151
7	B	56	54	56
8	B	52	55	52
9	B	55	53	55
10	B	53	56	56
11	B	52	54	52
12	B	54	56	54
13	C	28	29	29
14	C	28	32	30
15	C	30	29	32
16	D	100	98	102
17	D	102	101	102
18	D	98	99	100
19	D	102	102	102
20	D	100	98	102
21	E	122	124	125
22	E	122	124	128
23	E	123	128	125
24	E	127	122	123
25	E	126	123	123

Use the data in the table below to set up short-run X-bar and R charts using the DNOM approach. The nominal dimensions for each part are T(A) = 151.5, T(B) = 54.0, T(C) = 30.0, T(D) = 100.5, and T(E) = 124.5.

Sample Part M1 M2 M3
1 A 154 150 155
2 A 151 152 149
3 A 148 155 152
4 A 152 151 149
5 A 154 154 152
6 A 148 150 151
7 B 56 54 56
8 B 52 55 52
9 B 55 53 55
10 B 53 56 56
11 B 52 54 52
12 B 54 56 54
13 C 28 29 29
14 C 28 32 30
15 C 30 29 32
16 D 100 98 102
17 D 102 101 102
18 D 98 99 100
19 D 102 102 102
20 D 100 98 102
21 E 122 124 125
22 E 122 124 128
23 E 123 128 125
24 E 127 122 123
25 E 126 123 123

Added by Charles P.

Question

Please give Ace some feedback