• Home
  • Textbooks
  • Physics: Principles with Applications
  • DC CIRCUITS

Physics: Principles with Applications

Douglas C. Giancoli

Chapter 19

DC CIRCUITS - all with Video Answers

Educators

+ 1 more educators

Chapter Questions

03:14

Problem 1

(I) Calculate the terminal voltage for a battery with an internal resistance of 0.900 $\Omega$ and an emf of 6.00 V when the battery is connected in series with ($a$) a 71.0-$\Omega$ resistor, and ($b$) a 710-$\Omega$ resistor.

Ben Nicholson
Ben Nicholson
Numerade Educator
04:31

Problem 2

(I) Four 1.50-V cells are connected in series to a 12.0-$\Omega$ lightbulb. If the resulting current is 0.45 A, what is the internal resistance of each cell, assuming they are identical and neglecting the resistance of the wires?

Abhishek Jana
Abhishek Jana
Numerade Educator
02:20

Problem 3

(II) What is the internal resistance of a 12.0-V car battery whose terminal voltage drops to 8.8 V when the starter motor draws 95 A? What is the resistance of the starter?

Ben Nicholson
Ben Nicholson
Numerade Educator
03:28

Problem 4

(I) A 650-$\Omega$ and 1800-$\Omega$ an resistor are connected in series with a 12-V battery. What is the voltage across the 1800-$\Omega$ resistor?

Abhishek Jana
Abhishek Jana
Numerade Educator
01:49

Problem 5

(I) Three 45-$\Omega$ lightbulbs and three 65-$\Omega$ lightbulbs are connected in series. ($a$) What is the total resistance of the circuit? ($b$) What is the total resistance if all six are wired in parallel?

Ben Nicholson
Ben Nicholson
Numerade Educator
02:16

Problem 6

(II) Suppose that you have a 580-$\Omega$, a 790-$\Omega$, and a 1.20-k$\Omega$ resistor. What is ($a$) the maximum, and ($b$) the minimum resistance you can obtain by combining these?

Abhishek Jana
Abhishek Jana
Numerade Educator
01:08

Problem 7

(II) How many 10-$\Omega$ resistors must be connected in series to give an equivalent resistance to five 100-$\Omega$ resistors connected in parallel?

Ben Nicholson
Ben Nicholson
Numerade Educator
03:41

Problem 8

(II) Design a "voltage divider" (see Example 19-3) that would provide one-fifth (0.20) of the battery voltage across $R_2$ , Fig. 19-6. What is the ratio $R_1/R_2$?

Abhishek Jana
Abhishek Jana
Numerade Educator
04:05

Problem 9

(II) Suppose that you have a 9.0-V battery and wish to apply a voltage of only 3.5 V. Given an unlimited supply of 1.0-$\Omega$ resistors, how could you connect them to make a "voltage divider" that produces a 3.5-V output for a 9.0-V input?

Ben Nicholson
Ben Nicholson
Numerade Educator
05:38

Problem 10

(II) Three 1.70-k$\Omega$ resistors can be connected together in four different ways, making combinations of series and/or parallel circuits. What are these four ways, and what is the net resistance in each case?

Abhishek Jana
Abhishek Jana
Numerade Educator
04:36

Problem 11

(II) A battery with an emf of 12.0 V shows a terminal voltage of 11.8 V when operating in a circuit with two lightbulbs, each rated at 4.0 W (at 12.0 V), which are connected in parallel. What is the battery's internal resistance?

Ben Nicholson
Ben Nicholson
Numerade Educator
05:07

Problem 12

(II) Eight identical bulbs are connected in series across a 120-V line. ($a$) What is the voltage across each bulb? ($b$) If the current is 0.45 A, what is the resistance of each bulb, and what is the power dissipated in each?

Abhishek Jana
Abhishek Jana
Numerade Educator
04:30

Problem 13

(II) Eight bulbs are connected in parallel to a 120-V source by two long leads of total resistance 1.4 $\Omega$. If 210 mA flows through each bulb, what is the resistance of each, and what fraction of the total power is wasted in the leads?

Ben Nicholson
Ben Nicholson
Numerade Educator
03:29

Problem 14

(II) A close inspection of an electric circuit reveals that a 480-$\Omega$ resistor was inadvertently soldered in the place where a 350-$\Omega$ resistor is needed. How can this be fixed without removing anything from the existing circuit?

Abhishek Jana
Abhishek Jana
Numerade Educator
01:51

Problem 15

(II) Eight 7.0-W Christmas tree lights are connected in series to each other and to a 120-V source. What is the resistance of each bulb?

Ben Nicholson
Ben Nicholson
Numerade Educator
10:05

Problem 16

(II) Determine ($a$) the equivalent resistance of the circuit shown in Fig. 19-48, ($b$) the voltage across each resistor, and (c) the current through each resistor.
FIGURE 19–48 Problem 16.
(CAN'T COPY THE FIGURE)

Abhishek Jana
Abhishek Jana
Numerade Educator
01:22

Problem 17

(II) A 75-W, 120-V bulb is connected in parallel with a 25-W, 120-V bulb. What is the net resistance?

Ben Nicholson
Ben Nicholson
Numerade Educator
10:04

Problem 18

(II) ($a$) Determine the equivalent resistance of the "ladder" of equal 175-$\Omega$ resistors shown in Fig. 19-49. In other words, what resistance would an ohmmeter read if connected between
points A and B? ($b$) What is the current through each of the three resistors on the left if a 50.0-V battery is connected between points A and B?
FIGURE 19–49 Problem 18.
(CAN'T COPY THE FIGURE)

Abhishek Jana
Abhishek Jana
Numerade Educator
03:13

Problem 19

(II) What is the net resistance of the circuit connected to the battery in Fig. 19-50?
FIGURE 19–50 Problems 19 and 20.
(CAN'T COPY THE FIGURE)

Ben Nicholson
Ben Nicholson
Numerade Educator
13:37

Problem 20

(II) Calculate the current through each resistor in Fig. 19-50 if each resistance $R =$ 3.25 k$\Omega$ and $V =$ 12.0 V. What is the potential difference between points A and B?
FIGURE 19–50 Problems 19 and 20.
(CAN'T COPY THE FIGURE)

Abhishek Jana
Abhishek Jana
Numerade Educator
04:08

Problem 21

(III) Two resistors when connected in series to a 120-V line use one-fourth the power that is used when they are connected in parallel. If one resistor is 4.8 k$\Omega$, what is the resistance of the other?

Ben Nicholson
Ben Nicholson
Numerade Educator
12:16

Problem 22

(III) Three equal resistors ($R$) are connected to a battery as shown in Fig. 19-51. Qualitatively, what happens to ($a$) the voltage drop across each of these resistors, ($b$) the current flow through each, and ($c$) the terminal voltage of the battery, when the switch S is opened, after having been closed for a long time? ($d$) If the emf of the battery is 9.0 V, what is its terminal voltage when the switch is closed if the internal resistance $r$ is 0.50 $\Omega$ and $R =$ 5.50 $\Omega$? (e) What is the terminal voltage when the switch is open?
FIGURE 19–51 Problem 22.
(CAN'T COPY THE FIGURE)

Abhishek Jana
Abhishek Jana
Numerade Educator
06:08

Problem 23

(III) A 2.5-k$\Omega$ and a 3.7-k$\Omega$ resistor are connected in parallel; this combination is connected in series with a 1.4-k$\Omega$ resistor. If each resistor is rated at 0.5 W (maximum
without overheating), what is the maximum voltage that can be applied across the whole network?

Ben Nicholson
Ben Nicholson
Numerade Educator
13:56

Problem 24

(III) Consider the network of resistors shown in Fig. 19-52. Answer qualitatively: ($a$) What happens to the voltage across each resistor when the switch S is closed? ($b$)What happens to the current through each when the switch is closed? ($c$) What happens to the power output of the battery when the switch is closed? ($d$) Let $R_1 = R_2 = R_3 = R_4 =$ 155 $\Omega$ and $V =$ 22.0 V. Determine the current through each resistor before and after closing the switch. Are your qualitative predictions confirmed?
FIGURE 19–52 Problem 24.
(CAN'T COPY THE FIGURE)

Abhishek Jana
Abhishek Jana
Numerade Educator
02:33

Problem 25

(I) Calculate the current in the circuit of Fig. 19-53, and show that the sum of all the voltage changes around the circuit is zero.
FIGURE 19–53 Problem 25.
(CAN'T COPY THE FIGURE)

Ben Nicholson
Ben Nicholson
Numerade Educator
04:49

Problem 26

(II) Determine the terminal voltage of each battery in Fig. 19-54.
FIGURE 19–54 Problem 26.
(CAN'T COPY THE FIGURE)

Abhishek Jana
Abhishek Jana
Numerade Educator
04:22

Problem 27

(II) For the circuit shown in Fig. 19-55, find the potential difference between points a and b. Each resistor has $R =$ 160 $\Omega$ and each battery is 1.5 V.
FIGURE 19–55 Problem 27.
(CAN'T COPY THE FIGURE)

Ben Nicholson
Ben Nicholson
Numerade Educator
08:49

Problem 28

(II) Determine the magnitudes and directions of the currents in each resistor shown in Fig. 19-56. The batteries have emfs of $\mathscr{E}_1 =$ 9.0 V and $\mathscr{E}_2 =$ 12.0 V and the resistors
have values of $R_1 =$ 25$\Omega$, $R_2 =$ 68 $\Omega$, and $R_3 =$ 35 $\Omega$. ($a$) Ignore internal resistance of the batteries. ($b$) Assume each battery has internal resistance $r =$ 1.0 $\Omega$.
FIGURE 19–56 Problem 28.
(CAN'T COPY THE FIGURE)

Abhishek Jana
Abhishek Jana
Numerade Educator
12:22

Problem 29

(II) ($a$) What is the potential difference between points a and d in Fig. 19-57 (similar to Fig. 19-13, Example 19-8), and ($b$) what is the terminal voltage of each battery?
FIGURE 19–57 Problem 29.
(CAN'T COPY THE FIGURE)

Ben Nicholson
Ben Nicholson
Numerade Educator
10:26

Problem 30

(II) Calculate the magnitude and direction of the currents in each resistor of Fig. 19-58.
FIGURE 19–58 Problem 30.
(CAN'T COPY THE FIGURE)

Abhishek Jana
Abhishek Jana
Numerade Educator
02:48

Problem 31

(II) Determine the magnitudes and directions of the currents through $R_1$ and $R_2$ in Fig. 19-59.
FIGURE 19–59 Problems 31 and 32.
(CAN'T COPY THE FIGURE)

Ben Nicholson
Ben Nicholson
Numerade Educator
07:43

Problem 32

(II) Repeat Problem 31, now assuming that each battery has an internal resistance $r =$ 1.4 $\Omega$.
FIGURE 19–59 Problems 31 and 32.
(CAN'T COPY THE FIGURE)

Abhishek Jana
Abhishek Jana
Numerade Educator
05:15

Problem 33

(III) ($a$) A network of five equal resistors $R$ is connected to a battery $\mathscr{E}$ as shown in Fig. 19-60. Determine the current $I$ that flows out of the battery. ($b$) Use the value determined for $I$ to find thesingle resistor $R_{eq}$ that is equivalent to the five-resistor network.
FIGURE 19–60 Problem 33.
(CAN'T COPY THE FIGURE)

Ben Nicholson
Ben Nicholson
Numerade Educator
07:57

Problem 34

(III) ($a$) Determine the currents $I_1$ , $I_2$ , and $I_3$ in Fig. 19-61. Assume the internal resistance of each battery is $r =$ 1.0 $\Omega$. (b) What is the terminal voltage of the 6.0-V battery?
FIGURE 19–61 Problems 34 and 35.
(CAN'T COPY THE FIGURE)

Abhishek Jana
Abhishek Jana
Numerade Educator
06:14

Problem 35

(III) What would the current $I_1$ be in Fig. 19-61 if the 12-$\Omega$ resistor is shorted out (resistance $=$ 0)? Let $r =$ 1.0 $\Omega$.
FIGURE 19–61 Problems 34 and 35.
(CAN'T COPY THE FIGURE)

Ben Nicholson
Ben Nicholson
Numerade Educator
05:02

Problem 36

(II) Suppose two batteries, with unequal emfs of 2.00 V and 3.00V, are connected as shown in Fig. 19-62. If each internal resistance is $r =$ 0.350 $\Omega$, and $R =$ 4.00 $\Omega$, what is the voltage across the resistor $R$?
FIGURE 19–62 Problem 36.
(CAN'T COPY THE FIGURE)

Abhishek Jana
Abhishek Jana
Numerade Educator
01:59

Problem 37

(II) A battery for a proposed electric car is to have three hundred 3-V lithium ion cells connected such that the total voltage across all of the cells is 300 V. Describe a possible connection configuration (using series and parallel connections) that would meet these battery specifications.

Ben Nicholson
Ben Nicholson
Numerade Educator
03:18

Problem 38

(I) ($a$) Six 4.8-$\mu$F capacitors are connected in parallel. What is the equivalent capacitance? ($b$) What is their equivalent capacitance if connected in series?

Abhishek Jana
Abhishek Jana
Numerade Educator
01:21

Problem 39

(I) A 3.00-$\mu$F and a 4.00-$\mu$F capacitor are connected in series, and this combination is connected in parallel with a 2.00-$\mu$F capacitor (see Fig. 19-63). What is the net capacitance?
FIGURE 19–63 Problems 39 and 40.
(CAN'T COPY THE FIGURE)

Ben Nicholson
Ben Nicholson
Numerade Educator
05:06

Problem 40

(II) If 21.0 V is applied across the whole network of Fig. 19-63, calculate ($a$) the voltage across each capacitor and ($b$) the charge on each capacitor.
FIGURE 19–63 Problems 39 and 40.
(CAN'T COPY THE FIGURE)

Abhishek Jana
Abhishek Jana
Numerade Educator
01:52

Problem 41

(II) The capacitance of a portion of a circuit is to be reduced from 2900 pF to 1200 pF.What capacitance can be added to the circuit to produce this effect without removing existing circuit elements? Must any existing connections be broken to accomplish this?

Ben Nicholson
Ben Nicholson
Numerade Educator
00:57

Problem 42

(II) An electric circuit was accidentally constructed using a 7.0-$\mu$F capacitor instead of the required 16-$\mu$F value. Without removing the 7.0-$\mu$F capacitor, what can a technician
add to correct this circuit?

Abhishek Jana
Abhishek Jana
Numerade Educator
02:15

Problem 43

(II) Consider three capacitors, of capacitance 3200 pF, 5800 pF, and 0.0100 $\mu$F. What maximum and minimum capacitance can you form from these? How do you make the connection in each case?

Ben Nicholson
Ben Nicholson
Numerade Educator
02:10

Problem 44

(II) Determine the equivalent capacitance between points a and b for the combination of capacitors shown in Fig. 19-64.
FIGURE 19–64 Problem 44.
(CAN'T COPY THE FIGURE)

Abhishek Jana
Abhishek Jana
Numerade Educator
02:40

Problem 45

(II) What is the ratio of the voltage $V_1$ across capacitor $C_1$ in Fig. 19-65 to the voltage $V_2$ across capacitor $C_2$?
FIGURE 19–65 Problem 45.
(CAN'T COPY THE FIGURE)

Vishal Gupta
Vishal Gupta
Numerade Educator
05:10

Problem 46

(II) A 0.50-$\mu$F and a 1.4-$\mu$F capacitor are connected in series to a 9.0-V battery. Calculate ($a$) the potential difference across each capacitor and ($b$) the charge on each. ($c$) Repeat parts ($a$) and ($b$) assuming the two capacitors are in parallel.

Abhishek Jana
Abhishek Jana
Numerade Educator
02:00

Problem 47

(II) A circuit contains a single 250-pF capacitor hooked across a battery. It is desired to store four times as much energy in a combination of two capacitors by adding a single capacitor to this one. How would you hook it up, and what would its value be?

Ben Nicholson
Ben Nicholson
Numerade Educator
03:54

Problem 48

(II) Suppose three parallel-plate capacitors, whose plates have areas $A_1 , A_2 ,$ and $A_3$ and separations $d_1, d_2,$ and $d_3,$ are connected in parallel. Show, using only Eq. 17-8, that Eq. 19-5 is valid.

Abhishek Jana
Abhishek Jana
Numerade Educator
04:41

Problem 49

(II) Two capacitors connected in parallel produce an equivalent capacitance of 35.0 $\mu$F but when connected in series the equivalent capacitance is only 4.8 $\mu$F. What is the individual capacitance of each capacitor?

Ben Nicholson
Ben Nicholson
Numerade Educator
05:32

Problem 50

(III) Given three capacitors, $C_1 =$ 2.0 $\mu$F, $C_2 =$ 1.5 $\mu$F, and $C_3 =$ 3.0 $\mu$F, what arrangement of parallel and series connections with a 12-V battery will give the minimum voltage drop across the 2.0-$\mu$F capacitor? What is the minimum voltage drop?

Abhishek Jana
Abhishek Jana
Numerade Educator
09:51

Problem 51

(III) In Fig. 19-66, suppose $C_1 = C_2 = C_3 = C_4 = C$. ($a$) Determine the equivalent capacitance between points a and b. ($b$) Determine the charge on each capacitor and the potential
difference across each in terms of $V$.
FIGURE 19–66 Problem 51.
(CAN'T COPY THE FIGURE)

Ben Nicholson
Ben Nicholson
Numerade Educator
02:48

Problem 52

(I) Estimate the value of resistances needed to make a variable timer for intermittent windshield wipers: one wipe every 15 s, 8 s, 4 s, 2 s, 1 s. Assume the capacitor used is on the order of 1 $\mu$F. See Fig. 19-67.
FIGURE 19–67 Problem 52.
(CAN'T COPY THE FIGURE)

Abhishek Jana
Abhishek Jana
Numerade Educator
02:08

Problem 53

(II) Electrocardiographs are often connected as shown in Fig. 19-68. The lead wires to the legs are said to be capacitively coupled. A time constant of 3.0 s is typical and allows rapid changes in potential to be recorded accurately. If $C =$ 3.0 $\mu$F, what value must $R$ have?
FIGURE 19–68 Problem 53.
(CAN'T COPY THE FIGURE)

Ben Nicholson
Ben Nicholson
Numerade Educator
04:47

Problem 54

(II) In Fig. 19-69 (same as Fig. 19-20a), the total resistance is 15.0 k$\Omega$, and the battery's emf is 24.0 V. If the time constant is measured to be 18.0 $\mu$s, calculate ($a$) the total capacitance of the circuit and ($b$) the time it takes for the voltage across the resistor to reach 16.0 V after the switch is closed.
FIGURE 19–69 Problem 54.
(CAN'T COPY THE FIGURE)

Brandy Heflin
Brandy Heflin
Numerade Educator
02:15

Problem 55

(II) Two 3.8-$\mu$F capacitors, two 2.2-k$\Omega$ resistors, and a 16.0-V source are connected in series. Starting from the uncharged state, how long does it take for the current to drop from its initial value to 1.50 mA?

Prabhu Ramji
Prabhu Ramji
Numerade Educator
04:12

Problem 56

(II) The RC circuit of Fig. 19-70 (same as Fig. 19-21a) has $R =$ 8.7 k$\Omega$ and $C =$ 3.0 $\mu$F. The capacitor is at voltage $V_0$ at $t = 0$, when the switch is closed. How long does it take
the capacitor to discharge to 0.25% of its initial voltage?
FIGURE 19–70 Problem 56.
(CAN'T COPY THE FIGURE)

Abhishek Jana
Abhishek Jana
Numerade Educator
06:02

Problem 57

(III) Consider the circuit shown in Fig. 19-71, where all resistors have the same resistance $R$. At $t = 0$, with the capacitor $C$ uncharged, the switch is closed. ($a$) At $t = 0$, the three currents can be determined by analyzing a simpler, but equivalent, circuit. Draw this simpler circuit and use it to find the values of $I_1, I_2,$ and $I_3$ at $t = 0$ ($b$)At $t = \infty$. the currents can be determined by analyzing a simpler, equivalent circuit. Draw this simpler circuit and implement it in finding the values of $I_1, I_2,$ and $I_3$ at $t = \infty$. (c) At $t = \infty$, what is the potential difference across the capacitor?
FIGURE 19–71 Problem 57.
(CAN'T COPY THE FIGURE)

Ben Nicholson
Ben Nicholson
Numerade Educator
11:40

Problem 58

(III) Two resistors and two uncharged capacitors are arranged as shown in Fig. 19-72. Then a potential difference of 24 V is applied across the combination as shown. ($a$) What is the potential at point a with switch S open? (Let $V = 0$ at the negative terminal of the source.) ($b$)What is the potential at point b with the switch open? ($c$) When the switch is closed, what is the final potential of point b? ($d$) How much charge flows through the switch S after it is closed?
FIGURE 19–72 Problem 58.
(CAN'T COPY THE FIGURE)

Abhishek Jana
Abhishek Jana
Numerade Educator
01:43

Problem 59

(I) ($a$) An ammeter has a sensitivity of 35,000 $\Omega$/V. What current in the galvanometer produces full-scale deflection? ($b$) What is the resistance of a voltmeter on the 250-V scale if the meter sensitivity is 35,000 $\Omega$/V?

Ben Nicholson
Ben Nicholson
Numerade Educator
02:48

Problem 60

(II) An ammeter whose internal resistance is 53 $\Omega$ reads 5.25 mA when connected in a circuit containing a battery and two resistors in series whose values are 720 $\Omega$ and 480 $\Omega$.
What is the actual current when the ammeter is absent?

Abhishek Jana
Abhishek Jana
Numerade Educator
04:52

Problem 61

(II) A milliammeter reads 35 mA full scale. It consists of a 0.20-$\Omega$ resistor in parallel with a 33-$\Omega$ galvanometer. How can you change this ammeter to a voltmeter giving a full-scale
reading of 25 V without taking the ammeter apart? What will be the sensitivity ($\Omega$/V) of your voltmeter?

Ben Nicholson
Ben Nicholson
Numerade Educator
06:30

Problem 62

(II) A galvanometer has an internal resistance of 32 $\Omega$ and deflects full scale for a 55-$\mu$A current. Describe how to use this galvanometer to make ($a$) an ammeter to read currents up to 25 A, and ($b$) a voltmeter to give a full-scale deflection of 250 V.

Abhishek Jana
Abhishek Jana
Numerade Educator
06:07

Problem 63

(III) A battery with $\mathscr{E} =$ 12.0 V and internal resistance $r =$ 1.0 $\Omega$ is connected to two 7.5-k$\Omega$ resistors in series. An ammeter of internal resistance 0.50 $\Omega$ measures the current, and at the same time a voltmeter with internal resistance 15 k$\Omega$ measures the voltage across one of the 7.5-k$\Omega$ resistors in the circuit.What do the ammeter and voltmeter read? What is the %"error" from the current and voltage $without$ meters?

Ben Nicholson
Ben Nicholson
Numerade Educator
05:25

Problem 64

(III) What internal resistance should the voltmeter of
Example 19-17 have to be in error by less than 5%?

Abhishek Jana
Abhishek Jana
Numerade Educator
04:09

Problem 65

(III) Two 9.4-k$\Omega$ resistors are placed in series and connected to a battery.A voltmeter of sensitivity 1000 $\Omega$/V is on the 3.0-V scale and reads 1.9 V when placed across either resistor.What is the emf of the battery? (Ignore its internal resistance.)

Ben Nicholson
Ben Nicholson
Numerade Educator
05:55

Problem 66

(III) When the resistor $R$ in Fig. 19-73 is 35 $\Omega$, the high resistance voltmeter reads 9.7 V. When $R$ is replaced by a 14.0-$\Omega$ resistor, the voltmeter reading drops to 8.1 V. What are the emf and internal resistance of the battery?
FIGURE 19–73 Problem 66.
(CAN'T COPY THE FIGURE)

Abhishek Jana
Abhishek Jana
Numerade Educator
02:59

Problem 67

Suppose that you wish to apply a 0.25-V potential difference between two points on the human body. The resistance is about 1800 $\Omega$, and you only have a 1.5-V battery. How can you connect up one or more resistors to produce the desired voltage?

Ben Nicholson
Ben Nicholson
Numerade Educator
04:11

Problem 68

A $\textbf{three-way lightbulb}$ can produce 50W, 100W, or 150W, at 120 V. Such a bulb contains two filaments that can be connected to the 120 V individually or in parallel (Fig. 19-74). ($a$) Describe how the connections to the two filaments are made to give each of the three wattages. ($b$)What must be the resistance of each filament?
FIGURE 19–74 Problem 68.
(CAN'T COPY THE FIGURE)

Abhishek Jana
Abhishek Jana
Numerade Educator
08:27

Problem 69

What are the values of effective capacitance which can be
obtained by connecting four identical capacitors, each
having a capacitance $C$?

Ben Nicholson
Ben Nicholson
Numerade Educator
01:41

Problem 70

Electricity can be a hazard in hospitals, particularly to patients who are connected to electrodes, such as an ECG. Suppose that the motor of a motorized bed shorts out to the bed frame, and the bed frame's connection to a ground has broken (or was not there in the first place). If a nurse touches the bed and the patient at the same time, the nurse becomes a conductor and a complete circuit can be made through the patient to ground through the ECG apparatus. This is shown schematically in Fig. 19-75. Calculate the current through the patient.
FIGURE 19–75 Problem 70.
(CAN'T COPY THE FIGURE)

Abhishek Jana
Abhishek Jana
Numerade Educator
04:06

Problem 71

A heart pacemaker is designed to operate at 72 beats/min using a 6.5-$\mu$F capacitor in a simple $RC$ circuit.What value of resistance should be used if the pacemaker is to fire (capacitor discharge) when the voltage reaches 75% of maximum and then drops to 0 V (72 times a minute)?

Ben Nicholson
Ben Nicholson
Numerade Educator
04:41

Problem 72

Suppose that a person's body resistance is 950 $\Omega$ (moist skin). ($a$) What current passes through the body when the person accidentally is connected to 120 V? ($b$) If there is an alternative
path to ground whose resistance is 25 $\Omega$, what then is the current through the body? ($c$) If the voltage source can produce at most 1.5 A, how much current passes through the person in case ($b$)?

Abhishek Jana
Abhishek Jana
Numerade Educator
04:02

Problem 73

One way a multiple-speed ventilation fan for a car can be designed is to put resistors in series with the fan motor. The resistors reduce the current through the motor and make it run more slowly. Suppose the current in the motor is 5.0 A when it is connected directly across a 12-V battery. ($a$) What series resistor should be used to reduce the current to 2.0 A for low-speed operation? ($b$) What power
rating should the resistor have? Assume that the motor's resistance is roughly the same at all speeds.

Ben Nicholson
Ben Nicholson
Numerade Educator
03:44

Problem 74

A $\textbf{Wheatstone bridge}$ is a type of "bridge circuit" used to make measurements of resistance. The unknown resistance to be measured, $R_x,$ is placed in the circuit with accurately known resistances $R_1, R_2,$ and $R_3$ (Fig. 19-76). One of these, is a variable resistor which is adjusted so that when the switch is closed momentarily, the ammeter A shows zero current flow. The bridge is then said to be balanced. ($a$) Determine $R_x$ in terms of $R_1, R_2,$ and $R_3$. ($b$) If a Wheatstone bridge is "balanced" when $R_1 =$ 590 $\Omega$, $R_2 =$ 972 $\Omega$, and $R_3 =$ 78.6 $\Omega$, what is the value of the unknown resistance?
FIGURE 19–76 Problem 74. Wheatstone bridge.
(CAN'T COPY THE FIGURE)

Abhishek Jana
Abhishek Jana
Numerade Educator
03:06

Problem 75

The internal resistance of a 1.35-V mercury cell is 0.030 $\Omega$, whereas that of a 1.5-V dry cell is 0.35 $\Omega$. Explain why three mercury cells can more effectively power a 2.5-W hearing aid that requires 4.0 V than can three dry cells.

Ben Nicholson
Ben Nicholson
Numerade Educator
03:22

Problem 76

How many $\frac{1}{2}$-W resistors, each of the same resistance, must be used to produce an equivalent 3.2-k$\Omega$, 3.5-W resistor? What is the resistance of each, and how must they be
connected? Do not exceed $P = \frac{1}{2}$W in each resistor.

Abhishek Jana
Abhishek Jana
Numerade Educator
03:59

Problem 77

A $\textbf{solar cell}$, 3.0 cm square, has an output of 350 mA at 0.80 V when exposed to full sunlight. A solar panel that delivers close to 1.3 A of current at an emf of 120 V to an external load is needed. How many cells will you need to create the panel? How big a panel will you need, and how
should you connect the cells to one another?

Ben Nicholson
Ben Nicholson
Numerade Educator
06:39

Problem 78

The current through the 4.0-k$\Omega$ resistor in Fig. 19-77 is 3.10 mA. What is the terminal voltage $V_{ba}$ of the "unknown" battery? (There are two answers. Why?)
FIGURE 19–77 Problem 78.
(CAN'T COPY THE FIGURE)

Abhishek Jana
Abhishek Jana
Numerade Educator
04:11

Problem 79

A power supply has a fixed output voltage of 12.0V, but you need $V_T =$ 3.5 V output for an experiment. ($a$) Using the voltage divider shown in Fig. 19-78, what should $R_2$ be if $R_1$ is 14.5 $\Omega$ ? (b) What will the terminal voltage $V_T$ be if you connect a load to the 3.5-V output, assuming the load has a resistance of 7.0 $\Omega$?
FIGURE 19–78 Problem 79.
(CAN'T COPY THE FIGURE)

Ben Nicholson
Ben Nicholson
Numerade Educator
03:59

Problem 80

A battery produces 40.8 V when 8.40 A is drawn from it, and 47.3 V when 2.80 A is drawn. What are the emf and internal resistance of the battery?

Nishant Kumar
Nishant Kumar
Numerade Educator
04:02

Problem 81

In the circuit shown in Fig. 19-79, the 33-$\Omega$ resistor dissipates 0.80W. What is the battery voltage?
FIGURE 19–79 Problem 81.
(CAN'T COPY THE FIGURE)

Vishal Gupta
Vishal Gupta
Numerade Educator
10:17

Problem 82

For the circuit shown in Fig. 19-80, determine ($a$) the current through the 16-V battery and ($b$) the potential difference between points a and b, $V_a - V_b$.
FIGURE 19–80 Problem 82.
(CAN'T COPY THE FIGURE)

Abhishek Jana
Abhishek Jana
Numerade Educator
05:27

Problem 83

The current through the 20-$\Omega$ resistor in Fig. 19-81 does not change whether the two switches $S_1$ and $S_2$ are both open or both closed. Use this clue to determine the value
of the unknown resistance $R$.
FIGURE 19–81 Problem 83.
(CAN'T COPY THE FIGURE)

Ben Nicholson
Ben Nicholson
Numerade Educator
09:28

Problem 84

($a$) What is the equivalent resistance of the circuit shown in Fig. 19-82? [$Hint:$ Redraw the circuit to see series and parallel better.] ($b$) What is the current in the 14-$\Omega$ resistor? ($c$) What is the current in the 12-$\Omega$ resistor? ($d$)What is the power dissipation in the 4.5-$\Omega$ resistor?
FIGURE 19–82 Problem 84.
(CAN'T COPY THE FIGURE)

Abhishek Jana
Abhishek Jana
Numerade Educator
03:50

Problem 85

($a$) A voltmeter and an ammeter can be connected as shown in Fig. 19-83a to measure a resistance $R$. If $V$ is the voltmeter reading, and $I$ is the ammeter reading, the value of $R$ will not quite be $V/I$ (as in Ohm's law) because some current goes through the voltmeter. Show that the actual value of $R$ is
$$\frac{1}{R} =\frac{I}{V} -\frac{1}{R_V}1,$$
where $R_V$ is the voltmeter resistance. Note that $R \approx V/I$ if $R_V \gg R$. ($b$) A voltmeter and an ammeter can also be connected as shown in Fig. 19-83b to measure a resistance $R$. Show in this case that
$$R = \frac{V}{I} - R_A,$$
where $V$ and $I$ are the voltmeter and ammeter readings and $R_A$ is the resistance of the ammeter. Note that $R \approx V/I$ if $R_A \ll R$.
FIGURE 19–83 Problem 85.
(CAN'T COPY THE FIGURE)

Ben Nicholson
Ben Nicholson
Numerade Educator
05:45

Problem 86

The circuit shown in Fig. 19-84 uses a neon-filled tube as in Fig. 19-23a. This neon lamp has a threshold voltage $V_0$ for conduction, because no current flows until the neon gas in the tube is ionized by a sufficiently strong electric field. Once the threshold voltage is exceeded, the lamp has negligible resistance. The capacitor stores electrical energy, which can be released to flash the lamp. Assume that $C = 0.150 \mu$F, $R = 2.35 \times 10^6 \Omega, V_0 =$ 90.0 V, and $\mathscr{E} =$ 105 V. ($a$) Assuming the circuit is hooked up to the emf at time $t = 0$, at what time will the light first flash? ($b$) If the value of $R$ is increased, will the time you found in part ($a$) increase or decrease? ($c$) The flashing of the lamp is very brief.Why? ($d$) Explain what happens after the lamp flashes for the first time.
FIGURE 19–84 Problem 86.
(CAN'T COPY THE FIGURE)

Abhishek Jana
Abhishek Jana
Numerade Educator
01:52

Problem 87

A flashlight bulb rated at 2.0 W and 3.0 V is operated by a 9.0-V battery. To light the bulb at its rated voltage and power, a resistor $R$ is connected in series as shown in Fig. 19-85. What value should the resistor have?
FIGURE 19–85 Problem 87.
(CAN'T COPY THE FIGURE)

Ben Nicholson
Ben Nicholson
Numerade Educator
05:03

Problem 88

In Fig. 19-86, let $V =$ 10.0 V and $C_1 = C_2 = C_3 =$ 25.4 $\mu$F. How much energy is stored in the capacitor network ($a$) as shown, ($b$) if the capacitors were all in series, and ($c$) if the capacitors were all in parallel?
FIGURE 19–86 Problem 88.
(CAN'T COPY THE FIGURE)

Abhishek Jana
Abhishek Jana
Numerade Educator
03:20

Problem 89

A 12.0-V battery, two resistors, and two capacitors are connected as shown in Fig. 19-87. After the circuit has been connected for a long time, what is the charge on each capacitor?
FIGURE 19–87 Problem 89.
(CAN'T COPY THE FIGURE)

Ben Nicholson
Ben Nicholson
Numerade Educator
07:14

Problem 90

Determine the current in each resistor of the circuit shown in Fig. 19-88.
FIGURE 19–88 Problem 90.
(CAN'T COPY THE FIGURE)

Abhishek Jana
Abhishek Jana
Numerade Educator
03:16

Problem 91

How much energy must a 24-V battery expend to charge a 0.45-$\mu$F and a 0.20-$\mu$F capacitor fully when they are placed ($a$) in parallel, ($b$) in series? ($c$) How much charge flowed from the battery in each case?

Ben Nicholson
Ben Nicholson
Numerade Educator
08:41

Problem 92

Two capacitors, $C_1 =$ 2.2 $\mu$F and $C_2 =$ 1.2 $\mu$F, are connected in parallel to a 24-V source as shown in Fig. 19-89a. After they are charged they are disconnected from the source and from each other, and then reconnected directly to each other with plates of opposite sign connected together (see Fig. 19-89b). Find the charge on each capacitor and the potential across each after equilibrium is established (Fig.19-89c).
FIGURE 19–89 Problem 92.
(CAN'T COPY THE FIGURE)

Abhishek Jana
Abhishek Jana
Numerade Educator
05:07

Problem 93

The switch S in Fig. 19-90 is connected downward so that capacitor $C_2$ becomes fully charged by the battery of voltage $V_0$. If the switch is then connected upward, determine the charge on each capacitor after the switching.
FIGURE 19–90 Problem 93.
(CAN'T COPY THE FIGURE)

Ben Nicholson
Ben Nicholson
Numerade Educator
04:19

Problem 94

The performance of the starter circuit in a car can be significantly degraded by a small amount of corrosion on a battery terminal. Figure 19-91a depicts a properly functioning circuit with a battery (12.5-V emf, 0.02-$\Omega$ internal resistance) attached via corrosion-free cables to a starter motor of resistance $R_S =$ 0.15 $\Omega$. Sometime later, corrosion between a battery terminal and a starter cable introduces an extra series resistance of only $R_C =$ 0.10 $\Omega$ into the circuit as suggested in Fig. 19-91b. Let $P_0$ be the power delivered to the starter in the circuit free of corrosion, and let $P$ be the power delivered to the circuit with corrosion. Determine the ratio $P/P_0$.
FIGURE 19–91 Problem 94.
(CAN'T COPY THE FIGURE)

Abhishek Jana
Abhishek Jana
Numerade Educator
06:35

Problem 95

The variable capacitance of an old radio tuner consists of four plates connected together placed alternately between four other plates, also connected together (Fig. 19-92). Each plate is separated from its neighbor by 1.6 mm of air. One set of plates can move so that the area of overlap of each plate varies from 2.0 cm$^2$ to 9.0 cm$^2$. ($a$) Are these seven capacitors connected in series or in parallel? ($b$) Determine the range of capacitance values.
FIGURE 19–92 Problem 95.
(CAN'T COPY THE FIGURE)

Ben Nicholson
Ben Nicholson
Numerade Educator
04:12

Problem 96

A 175-pF capacitor is connected in series with an unknown capacitor, and as a series combination they are connected to a 25.0-V battery. If the 175-pF capacitor stores 125 pC of charge on its plates, what is the unknown capacitance?

Abhishek Jana
Abhishek Jana
Numerade Educator
07:31

Problem 97

In the circuit shown in Fig. 19-93, $C_1 =$ 1.0 $\mu$F, $C_2 =$ 2.0 $\mu$F, $C_3 =$ 2.4 $\mu$F, and a voltage $V_{ab} =$ 24 V is applied across points a and b. After $C_1$ is fully charged, the switch is thrown to the right. What is the final charge and potential difference on each capacitor?
FIGURE 19–93 Problem 97.
(CAN'T COPY THE FIGURE)

Ben Nicholson
Ben Nicholson
Numerade Educator