Fundamentals of Fluid Mechanics

Bruce R. Munson, Theodore H. Okiishi, Wade W. Huebsch

Chapter 2

Fluid Statics - all with Video Answers

Educators

+ 6 more educators

Chapter Questions

Problem 1

Obtain a photograph/image of a situation in which the fact that in a static fluid the pressure increases with depth is important. Print this photo and write a brief paragraph that describes the situation involved.

Surendra Kumar

Surendra Kumar

Numerade Educator

Problem 2

A closed, 5 -m-tall tank is filled with water to a depth of $4 \mathrm{m}$ The top portion of the tank is filled with air which, as indicated by a pressure gage at the top of the tank, is at a pressure of $20 \mathrm{kPa}$. Determine the pressure that the water exerts on the bottom of the $\operatorname{tank}$.

Narayan Hari

Numerade Educator

Problem 3

A closed tank is partially filled with glycerin. If the air pressure in the tank is $6 \mathrm{lb} / \mathrm{in}$. $^{2}$ and the depth of glycerin is $10 \mathrm{ft}$ what is the pressure in $\mathrm{Ib} / \mathrm{ft}^{2}$ at the bottom of the tank?

Narayan Hari

Numerade Educator

Problem 4

Blood pressure is usually given as a ratio of the maximum pressure (systolic pressure) to the minimum pressure (diastolic pressure $) .$ As shown in Video $\mathrm{V} 2.3,$ such pressures are commonly measured with a mercury manometer. A typical value for this ratio for a human would be $120 / 70$, where the pressures are in $\mathrm{mm}$ Hg.
(a) What would these pressures be in pascals? (b) If your car tire was inflated to $120 \mathrm{mm}$ Hg, would it be sufficient for normal driving?

Supratim Pal

Numerade Educator

Problem 5

An unknown immiscible liquid seeps into the bottom of an open oil tank. Some measurements indicate that the depth of the unknown liquid is $1.5 \mathrm{m}$ and the depth of the oil (specific weight $=8.5 \mathrm{kN} / \mathrm{m}^{3}$ ) floating on top is $5.0 \mathrm{m}$. A pressure gage connected to the bottom of the tank reads 65 kPa. What is the specific gravity of the unknown liquid?

Supratim Pal

Numerade Educator

Problem 6

The water level in an open standpipe is $80 \mathrm{ft}$ above the ground. What is the static pressure at a fire hydrant that is connected to the standpipe and located at ground level? Express your answer in psi.

Supratim Pal

Numerade Educator

Problem 7

How high a column of SAE 30 oil would be required to give the same pressure as $700 \mathrm{mm} \mathrm{Hg} ?$

Narayan Hari

Numerade Educator

Problem 8

What pressure, expressed in pascals, will a skin diver be subjected to at a depth of $40 \mathrm{m}$ in seawater?

Narayan Hari

Numerade Educator

Problem 9

Bathyscaphes are capable of submerging to great depths in the ocean. What is the pressure at a depth of $5 \mathrm{km},$ assuming that seawater has a constant specific weight of $10.1 \mathrm{kN} / \mathrm{m}^{3} ?$ press your answer in pascals and psi.

Supratim Pal

Numerade Educator

Problem 10

For the great depths that may be encountered in the ocean the compressibility of seawater may become an important consideration.
(a) Assume that the bulk modulus for seawater is constant and derive a relationship between pressure and depth which takes into account the change in fluid density with depth.
(b) Make use of part (a) to determine the pressure at a depth of $6 \mathrm{km}$ assuming seawater has a bulk modulus of $2.3 \times 10^{\circ} \mathrm{Pa}$ and a density of 1030 $\mathrm{kg} / \mathrm{m}^{3}$ at the surface. Compare this result with that obtained by assuming a constant density of $1030 \mathrm{kg} / \mathrm{m}^{3}$.

Anand Jangid

Numerade Educator

Problem 11

Sometimes when riding an elevator or driving up or down a hilly road a person's ears "pop" as the pressure difference between the inside and outside of the ear is cqualized. Determine the pressure difference (in psi) associated with this phenomenon if it occurs during a 150 -ft elevation change.

Supratim Pal

Numerade Educator

Problem 12

Develop an expression for the pressure variation in a liquid in which the specific weight increases with depth, $h,$ as $\gamma=K h+\gamma_{0}$ where $K$ is a constant and $\gamma_{0}$ is the specific weight at the free surface.

Supratim Pal

Numerade Educator

Problem 13

In a certain liquid at rest, measurements of the specific weight at various depths show the following variation:
$$\begin{array}{cc}\boldsymbol{h}(\mathbf{f t}) & \boldsymbol{\gamma}\left(\mathbf{b} / \mathbf{f t}^{3}\right) \\
\hline 0 & 70 \\10 & 76 \\20 & 84 \\30 & 91 \\40 & 97 \\50 & 102 \\60 & 107 \\70 & 110 \\80 & 112 \\90 & 114 \\
100 & 115 \\\hline\end{array}$$
The depth $h=0$ corresponds to a free surface at atmospheric pressure. Determine, through numerical integration of Eq. $2.4,$ the corresponding variation in pressure and show the results on a plot of pressure (in psf) versus depth (in feet).

Surendra Kumar

Numerade Educator

Problem 14

Because of elevation differences, the water pressure in the second floor of your house is lower than it is in the first floor. For tall buildings this pressure difference can become unacceptable. Discuss possible ways to design the water distribution system in very tall buildings so that the hydrostatic pressure difference is within acceptable limits.

Khoobchandra Agrawal

Khoobchandra Agrawal

Numerade Educator

Problem 15

Under normal conditions the temperature of the atmosphere decreases with increasing elevation. In some situations, however, a temperature inversion may exist so that the air temperature increases with elevation. A series of temperature probes on a mountain give the elevation-temperature data shown in the table below. If the barometric pressure at the base of the mountain is 12.1 psia, determine by means of numerical integration the pressure at the top of the mountain.
$$\begin{array}{cc}\hline \text { Elevation (ft) } & \text { Temperature ('F) } \\\hline 5000 & 50.1 \text { (base) } \\5500 & 55.2 \\
6000 & 60.3 \\6400 & 62.6 \\7100 & 67.0 \\7400 & 68.4 \\8200 & 70.0 \\8600 & 69.5 \\9200 & 68.0 \\9900 & 67.1 \text { (top) } \\
\hline\end{array}$$

Supratim Pal

Numerade Educator

Problem 16

Although it is difficult to compress water, the density of water at the bottom of the ocean is greater than that at the surface because of the higher pressure at depth. Estimate how much higher the ocean's surface would be if the density of seawater were instantly changed to a uniform density equal to that at the surface.

Mayukh Banik

Numerade Educator

Problem 17

(See Fluids in the News article titled ".Giraffe's blood pressure," Section 2.3.1.) (a) Determine the change in hydrostatic pressure in a giraffe's head as it lowers its head from eating leaves $6 \mathrm{m}$ above the ground to getting a drink of water at ground level as shown in Fig. P2.17. Assume the specific gravity of blood is $S G=1 .$ (b) Compare the pressure change calculated in part (a) to the normal $120 \mathrm{mm}$ of mercury pressure in a human's heart.

Ajay Singhal

Numerade Educator

Problem 18

What would be the barometric pressure reading, in $\mathrm{mm} \mathrm{Hg}$ at an elevation of $4 \mathrm{km}$ in the U.S. standard atmosphere? (Refer to Table $C .2$ in Appendix C.)

Narayan Hari

Numerade Educator

Problem 19

An absolute pressure of 7 psia corresponds to what gage pressure for standard atmospheric pressure of 14.7 psia?

Narayan Hari

Numerade Educator

Problem 20

Assume that a person skiing high in the mountains at an altitude of $15,000 \mathrm{ft}$ takes in the same volume of air with each breath as she does while walking at sea level. Determine the ratio of the mass of oxygen inhaled for each breath at this high altitude compared to that at sea level.

Prashant Bana

Numerade Educator

Problem 21

Pikes Peak near Denver, Colorado, has an elevation of $14,110 \mathrm{ft}$
(a) Determine the pressure at this elevation, based on Eq. $2.12 .$ (b) If the air is assumed to have a constant specific weight of $0.07647 \mathrm{lb} / \mathrm{ft}^{3},$ what would the pressure be at this altitude? (c) If the air is assumed to have a constant temperature of $59^{\circ} \mathrm{F}$, what would the pressure be at this elevation? For all three cases assume standard atmospheric conditions at sea level (see Table 2.1 ).

Narayan Hari

Numerade Educator

Problem 22

Equation 2.12 provides the relationship between pressure and elevation in the atmosphere for those regions in which the temperature varies linearly with elevation. Derive this equation and verify the value of the pressure given in Table $C .2$ in Appendix $C$ for an elevation of $5 \mathrm{km}$.

Supratim Pal

Numerade Educator

Problem 23

As shown in Fig. 2.6 for the U.S. standard atmosphere, the troposphere extends to an altitude of $11 \mathrm{km}$ where the pressure is $22.6 \mathrm{kPa}(\text { abs }) .$ In the next layer, called the stratosphere, the temperature remains constant at $-56.5^{\circ} \mathrm{C}$. Determine the pressure and density in this layer at an altitude of $15 \mathrm{km}$. Assume $g=9.77 \mathrm{m} / \mathrm{s}^{2}$ in your calculations. Compare your results with those given in Table C.2 in Appendix C.

Supratim Pal

Numerade Educator

Problem 24

(See Fluids in the News article titled "Weather, barometers, and bars," Section 2.5.) The record low sea-level barometric pressure ever recorded is 25.8 in. of mercury. At what altitude in the standard atmosphere is the pressure equal to this value?

Supratim Pal

Numerade Educator

Problem 25

On a given day, a barometer at the base of the Washington Monument reads 29.97 in. of mercury. What would the barometer reading be when you carry it up to the observation deck $500 \mathrm{ft}$ above the base of the monument?

Rashmi Sinha

Numerade Educator

Problem 26

Aneroid barometers can be used to measure changes in altitude. If a barometer reads 30.1 in. Hg at one elevation, what has been the change in altitude in meters when the barometer reading is 28.3 in. Hg? Assume a standard atmosphere and that Eq. 2.12 is applicable over the range of altitudes of interest.

Amit Srivastava

Amit Srivastava

Numerade Educator

Problem 27

Bourdon gages (see Video $\mathrm{V} 2.4$ and Fig. 2.13 ) are commonly used to measure pressure. When such a gage is attached to the closed water tank of Fig. $\mathrm{P} 2.27$ the gage reads 5 psi. What is the absolute air pressure in the tank? Assume standard atmospheric pressure of 14.7 psi.

Supratim Pal

Numerade Educator

Problem 28

On the suction side of a pump, a Bourdon pressure gage reads $40 \mathrm{kPa}$ vacuum. What is the corresponding absolute pressure if the local atmospheric pressure is $100 \mathrm{kPa}(\mathrm{abs}) ?$

Supratim Pal

Numerade Educator

Problem 29

A Bourdon pressure gage attached to the outside of a tank containing air reads 77.0 psi when the local atmospheric pressure is $760 \mathrm{mm}$ Hg. What will be the gage reading if the atmospheric pressure increases to $773 \mathrm{mm} \mathrm{Hg} ?$

Narayan Hari

Numerade Educator

Problem 30

Obtain a photograph/image of a situation in which the use of a manometer is important. Print this photo and write a brief paragraph that describes the situation involved.

Surendra Kumar

Numerade Educator

Problem 31

A water-filled U-tube manometer is used to measure the pressure inside a tank that contains air. The water level in the U-tube on the side that connects to the tank is $5 \mathrm{ft}$ above the base of the tank. The water level in the other side of the U-tube (which is open to the atmosphere) is $2 \mathrm{ft}$ above the base. Determine the pressure within the tank.

James Kiss

Numerade Educator

Problem 32

A barometric pressure of 29.4 in. Hg corresponds to what value of atmospheric pressure in psia, and in pascals?

Narayan Hari

Numerade Educator

Problem 33

For an atmospheric pressure of $101 \mathrm{kPa}$ (abs) determine the heights of the fluid columns in barometers containing one of the following liquids: (a) mercury, (b) water, and (c) ethyl alcohol. Calculate the heights including the effect of vapor pressure and compare the results with those obtained neglecting vapor pressure. Do these results support the widespread use of mercury for barometers? Why?

Surendra Kumar

Numerade Educator

Problem 34

The closed tank of Fig. $P .2 .34$ is filled with water and is $5 \mathrm{ft}$ long. The pressure gage on the tank reads 7 psi. Determine: (a) the height, $h,$ in the open water column, (b) the gage pressure acting on the bottom tank surface $A B,$ and (c) the absolute pressure of the air in the top of the tank if the local atmospheric pressure is 14.7 psia.

Surendra Kumar

Numerade Educator

Problem 35

A mercury manometer is connected to a large reservoir of water as shown in Fig. P2.35. Determine the ratio, $h_{w} / h_{m},$ of the distances $h_{w}$ and $h_{m}$ indicated in the figure.

Narayan Hari

Numerade Educator

Problem 36

A U-tube mercury manometer is connected to a closed pressurized tank as illustrated in Fig. P2.36. If the air pressure is 2 psi, determine the differential reading, $h$. The specific weight of the air is negligible.

Susan Hallstrom

Susan Hallstrom

Numerade Educator

Problem 37

A U-tube manometer is connected to a closed tank containing air and water as shown in Fig. $\mathrm{P} 2.37$. At the closed end of the manometer the air pressure is 16 psia. Determine the reading on the pressure gage for a differential reading of $4 \mathrm{ft}$ on the manometer. Express your answer in psi (gage). Assume standard atmospheric pressure and neglect the weight of the air columns in the manometer.

Narayan Hari

Numerade Educator

Problem 38

Compartments $A$ and $B$ of the tank shown in Fig. $P 2.38$ are closed and filled with air and a liquid with a specific gravity equal to $0.6 .$ Determine the manometer reading, $h,$ if the barometric pressure is 14.7 psia and the pressure gage reads 0.5 psi. The effect of the weight of the air is negligible.

Rashmi Sinha

Numerade Educator

Problem 39

A closed cylindrical tank filled with water has a hemispherical dome and is connected to an inverted piping system as shown in Fig. $\mathrm{P} 2.39 .$ The liquid in the top part of the piping system has a specific gravity of $0.8,$ and the remaining parts of the system are filled with water. If the pressure gage reading at $A$ is $60 \mathrm{kPa},$ determine
(a) the pressure in pipe $B,$ and (b) the pressure head, in millimeters of mercury, at the top of the dome (point $C$ ).

Prashant Bana

Numerade Educator

Problem 40

Two pipes are connected by a manometer as shown in Fig. P2.40. Determine the pressure difference, $p_{\lambda}-p_{\mathrm{B}},$ between the pipes.

Rashmi Sinha

Numerade Educator

Problem 41

An inverted open tank is held in place by a force $R$ as shown in Fig. $\mathrm{P} 2.41 .$ If the specific gravity of the manometer fluid is 2.5 determine the value of $h$.

James Kiss

Numerade Educator

Problem 42

A U-tube manometer is connected to a closed tank as shown in Fig. P2.42. The air pressure in the tank is 0.50 psi and the liquid in the tank is oil $\left(\gamma=54.0 \mathrm{lb} / \mathrm{ft}^{3}\right) .$ The pressure at point $A$ is 2.00 psi. Determine:
(a) the depth of oil, $z,$ and (b) the differential reading, $h,$ on the manometer.

Prabhat Tyagi

Numerade Educator

Problem 43

For the inclined-tube manometer of Fig. $\mathrm{P} 2.43,$ the pressure in pipe $A$ is 0.6 psi. The fluid in both pipes $A$ and $B$ is water, and the gage fluid in the manometer has a specific gravity of $2.6 .$ What is the pressure in pipe $B$ corresponding to the differential reading shown?

Prabhat Tyagi

Numerade Educator

Problem 44

A flowrate measuring device is installed in a horizontal pipe through which water is flowing. A U-tube manometer is connected to the pipe through pressure taps located 3 in. on either side of the device. The gage fluid in the manometer has a specific weight of 112 lb/ft $^{3}$. Determine the differential reading of the manometer corresponding to a pressure drop between the taps of $0.5 \mathrm{lb} / \mathrm{in.}^{2}$.

Nicholas Mogoi

Numerade Educator

Problem 45

Small differences in gas pressures are commonly measured with a micromanometer of the type illustrated in Fig. P2.45. This device consists of two large reservoirs each having a crosssectional area $A_{r}$ which are filled with a liquid having a specific weight $\gamma_{1}$ and connected by a U-tube of cross-sectional area $A_{i}$ containing a liquid of specific weight $\gamma_{2}$. When a differential gas pressure $p_{1}-p_{2},$ is applied, a differential reading, $h,$ develops. It is desired to have this reading sufficiently large (so that it can be easily read) for small pressure differentials. Determine the relationship between $h$ and $p_{1}-p_{2}$ when the area ratio $A_{i} / A,$ is small, and show that the differential reading, $h,$ can be magnified by making the difference in specific weights, $\gamma_{2}-\gamma_{1},$ small. Assume that initially (with $p_{1}=p_{2}$ ) the fluid levels in the two reservoirs are equal.

Dominador Tan

Numerade Educator

Problem 46

The cylindrical tank with hemispherical ends shown in Fig. $\mathrm{P} 2.46$ contains a volatile liquid and its vapor. The liquid density is $800 \mathrm{kg} / \mathrm{m}^{3},$ and its vapor density is negligible. The pressure in the vapor is $120 \mathrm{kPa}$ (abs) and the atmospheric pressure is $101 \mathrm{kPa}(\text { abs }) .$ Determine:
(a) the gage pressure reading on the pressure gage, and
(b) the height, $h,$ of the mercury, manometer.

Narayan Hari

Numerade Educator

Problem 47

Determine the elevation difference, $\Delta h,$ between the water levels in the two open tanks shown in Fig. P2.47.

Amit Srivastava

Amit Srivastava

Numerade Educator

Problem 48

Water, oil, and an unknown fluid are contained in the vertical tubes shown in Fig. $\mathrm{P} 2.48 .$ Determine the density of the unknown fluid.

Prabhat Tyagi

Numerade Educator

Problem 49

For the configuration shown in Fig. $\mathrm{P} 2.49$ what must be the value of the specific weight of the unknown fluid? Express your answer in $\mathrm{Ib} / \mathrm{ft}^{3}$.

Narayan Hari

Numerade Educator

Problem 50

An air-filled, hemispherical shell is attached to the ocean floor at a depth of 10 in. as shown in Fig. P2.50. A mercury barometer located inside the shell reads $765 \mathrm{mm}$ Hg, and a mercury U-tube manometer designed to give the outside water pressure indicates differential reading of $735 \mathrm{mm}$ Hg as illustrated. Based on these data, what is the atmospheric pressure at the ocean surface?

Prabhat Tyagi

Numerade Educator

Problem 51

Water, oil, and salt water fill a tube as shown in Fig. P2.51. Determine the pressure at point 1 (inside the closed tube).

Supratim Pal

Numerade Educator

Problem 52

Both ends of the U-tube mercury manometer of Fig. P2.52 are initially open to the atmosphere and under standard atmospheric pressure. When the valve at the top of the right leg is open, the level of mercury below the valve is $h_{1}$. After the valve is closed, air pressure is applied to the left leg. Determine the relationship between the differential reading on the manometer and the applied gage pressure, $p_{g}$. Show on a plot how the differential reading varies with $p_{g}$ for $h_{1}=25,50,75,$ and $100 \mathrm{mm}$ over the range $0 \leq p_{\mathrm{g}} \leq$ $300 \mathrm{kPa} .$ Assume that the temperature of the trapped air remains constant.

Victor Salazar

Numerade Educator

Problem 53

The inverted U-tube manometer of Fig. P2.53 contains oil $(S G=0.9)$ and water as shown. The pressure differential between pipes $A$ and $B, p_{A}-p_{B},$ is -5 kPa. Determine the differential reading $h$.

Narayan Hari

Numerade Educator

Problem 54

An inverted U-tube manometer containing oil $(S G=0.8)$ is located between two reservoirs as shown in Fig. P2.54. The reservoir on the left, which contains carbon tetrachloride, is closed and pressurized to 8 psi. The reservoir on the right contains water and is open to the atmosphere. With the given data, determine the depth of water, $h,$ in the right reservoir.

Amit Srivastava

Amit Srivastava

Numerade Educator

Problem 55

Three different liquids with properties as indicated fill the tank and manometer tubes as shown in Fig. P2.55. Determine the specific gravity of Fluid 3.

Prabhat Tyagi

Numerade Educator

Problem 56

Determine the pressure of the water in pipe $A$ shown in Fig. P2.56 if the gage pressure of the air in the tank is 2 psi.

Prabhat Tyagi

Numerade Educator

Problem 57

In Fig. $\mathrm{P} 2.57$ pipe $A$ contains carbon tetrachloride $(S G=$ 1.60) and the closed storage tank $\bar{B}$ contains a salt brine $(S G=$ 1.15). Determine the air pressure in tank $B$ if the pressure in pipe $A$ is 25 psi.

Prabhat Tyagi

Numerade Educator

Problem 58

In Fig. $\mathrm{P} 2.58$ pipe $A$ contains gasoline $(S G=0.7),$ pipe $B$ contains oil $(S G=0.9),$ and the manometer fluid is mercury. Determine the new differential reading if the pressure in pipe $A$ is decreased $25 \mathrm{kPa}$, and the pressure in pipe $B$ remains constant. The initial differential reading is $0.30 \mathrm{m}$ as shown.

Supratim Pal

Numerade Educator

Problem 59

The mercury manometer of Fig. $\mathrm{P} 2.59$ indicates a differential reading of $0.30 \mathrm{m}$ when the pressure in pipe $A$ is $30-\mathrm{mm} \mathrm{Hg}$ vacuum. Determine the pressure in pipe $B$.

Narayan Hari

Numerade Educator

Problem 60

The inclined differential manometer of Fig. P2.60 contains carbon tetrachloride. Initially the pressure differential between pipes $A$ and $B,$ which contain a brine $(S G=1.1),$ is zero as illustrated in the figure. It is desired that the manometer give a differential reading of 12 in. (measured along the inclined tube) for a pressure differential of 0.1 psi. Determine the required angle of inclination, $\bar{\theta}$.

Narayan Hari

Numerade Educator

Problem 61

The manometer fluid in the manometer of Fig. P2.61 has a specific gravity of $3.46 .$ Pipes $A$ and $B$ both contain water. If the pressure in pipe $A$ is decreased by 1.3 psi and the pressure in pipe $B$ increases by 0.9 psi, determine the new differential reading of the manometer.

Prabhat Tyagi

Numerade Educator

Problem 62

Determine the new differential reading along the inclined leg of the mercury manometer of Fig. $\mathrm{P} 2.62,$ if the pressure in pipe $A$ is decreased $10 \mathrm{kPa}$ and the pressure in pipe $B$ remains unchanged. The fluid in $A$ has a specific gravity of 0.9 and the fluid in $B$ is water.

Prabhat Tyagi

Numerade Educator

Problem 63

Determine the ratio of areas, $A_{1} / A_{2},$ of the two manometer legs of Fig. $\mathrm{P} 2.63$ if a change in pressure in pipe $B$ of 0.5 psi gives a corresponding change of 1 in. in the level of the mercury in the right leg. The pressure in pipe $A$ does not change.

Amit Srivastava

Amit Srivastava

Numerade Educator

Problem 64

Determine the change in the elevation of the mercury in the left leg of the manometer of Fig. $\mathrm{P} 2.64$ as a result of an increase in pressure of 5 psi in pipe $A$ while the pressure in pipe $B$ remains constant.

Rashmi Sinha

Numerade Educator

Problem 65

The U-shaped tube shown in Fig. 2.65 initially contains water only. A second liquid with specific weight, $\gamma$, less than water is placed on top of the water with no mixing occurring. Can the height, $h$, of the second liquid be adjusted so that the left and right levels are at the same height? Provide proof of your answer.

Supratim Pal

Numerade Educator

Problem 66

An inverted hollow cylinder is pushed into the water as is shown in Fig. $\mathrm{P} 2.66 .$ Determine the distance, $\ell$, that the water rises in the cylinder as a function of the depth, $d$, of the lower edge of the cylinder. Plot the results for $0 \leq d \leq H,$ when $H$ is equal to $1 \mathrm{m} .$ Assume the temperature of the air within the cylinder remains constant.

Victor Salazar

Numerade Educator

Problem 67

Obtain a photograph/image of a situation in which the hydrostatic force on a plane surface is important. Print this photo and write a brief paragraph that describes the situation involved.

Surendra Kumar

Numerade Educator

Problem 68

The basic elements of a hydraulic press are shown in Fig. $\mathrm{P} 2.68 .$ The plunger has an area of 1 in. $^{2},$ and a force, $F_{1},$ can be applied to the plunger through a lever mechanism having a mechanical advantage of 8 to $1 .$ If the large piston has an area of 150 in. $^{2},$ what load, $F_{2},$ can be raised by a force of 30 lb applied to the lever? Neglect the hydrostatic pressure variation.

Supratim Pal

Numerade Educator

Problem 69

A 0.3 -m-diameter pipe is connected to a 0.02 -m-diameter pipe, and both are rigidly held in place. Both pipes are horizontal with pistons at each end. If the space between the pistons is filled with water, what force will have to be applied to the larger piston to balance a force of $90 \mathrm{N}$ applied to the smaller piston? Neglect friction.

Supratim Pal

Numerade Educator

Problem 70

A Bourdon gage (see Fig. 2.13 and Video $\mathrm{V} 2.4$ ) is of ten used to measure pressure. One way to calibrate this type of gage is to use the arrangement shown in Fig. P2.70 a. The container is filled with a liquid and a weight, $\%$, placed on one side with the gage on the other side. The weight acting on the liquid through a 0.4 -in.- -diameter opening creates a pressure that is transmitted to the gage. This arrangement, with a series of weights, can be used to determine what a change in the dial movement, $\theta$, in Fig. $\mathrm{P} 2.70 b$ corresponds to in terms of a change in pressure. For a particular gage, some data are given below. Based on a plot of these data, determine the relationship between $\theta$ and the pressure, $p$, where $p$ is measured in psi.
$$\begin{array}{c|c|c|c|c|c|c|c|}\% \text { (lb) } & 0 & 1.04 & 2.00 & 3.23 & 4.05 & 5.24 & 6.31 \\
\hline \theta \text { (deg.) } & 0 & 20 & 40 & 60 & 80 & 100 & 120\end{array}$$

James Kiss

Numerade Educator

Problem 71

An inverted 0.1 -m-diameter circular cylinder is partially filled with water and held in place as shown in Fig. P2.71. A force of $20 \mathrm{N}$ is needed to pull the flat plate from the cylinder. Determine the air pressure within the cylinder. The plate is not fastened to the cylinder and has negligible mass.

Ajay Singhal

Numerade Educator

Problem 72

You partially fill a glass with water, place an index card on top of the glass, and then turn the glass upside down while holding the card in place. You can then remove your hand from the card and the card remains in place, holding the water in the glass. Explain how this works.

Supratim Pal

Numerade Educator

Problem 73

A piston having a cross-sectional area of $0.07 \mathrm{m}^{2}$ is located in a cylinder containing water as shown in Fig. P2.73. An open U-tube manometer is connected to the cylinder as shown. For $h_{1}=$ $60 \mathrm{mm}$ and $h=100 \mathrm{mm},$ what is the value of the applied force, $P$ acting on the piston? The weight of the piston is negligible.

Narayan Hari

Numerade Educator

Problem 74

A 6 -in.- -diameter piston is located within a cylinder that is connected to a $\frac{1}{2}$ -in.-diameter inclined-tube manometer as shown in Fig. P2.74. The fluid in the cylinder and the manometer is oil (specific weight $=59 \mathrm{lb} / \mathrm{ft}^{3}$ ). When a weight, $\%,$ is placed on the top of the cylinder, the fluid level in the manometer tube rises from point (1) to $(2) .$ How heavy is the weight? Assume that the change in position of the piston is negligible.

James Kiss

Numerade Educator

Problem 75

A square gate $(4 \mathrm{m} \text { by } 4 \mathrm{m})$ is located on the $45^{\circ}$ face of a dam. The top edge of the gate lies $8 \mathrm{m}$ below the water surface. Determine the force of the water on the gate and the point through which it acts.

Supratim Pal

Numerade Educator

Problem 76

A large, open tank contains water and is connected to a 6 ft-diameter conduit as shown in Fig. P2.76. A circular plug is used to seal the conduit. Determine the magnitude, direction, and location of the force of the water on the plug.

Narayan Hari

Numerade Educator

Problem 77

A circular 2 -m-diameter gate is located on the sloping side of a swimming pool. The side of the pool is oriented $60^{\circ}$ relative to the horizontal bottom, and the center of the gate is located $3 \mathrm{m}$ below the water surface. Determine the magnitude of the water force acting on the gate and the point through which it acts.

James Kiss

Numerade Educator

Problem 78

A vertical rectangular gate is $8 \mathrm{ft}$ wide and $10 \mathrm{ft}$ long and weighs 6000 lb. The gate slides in vertical slots in the side of a reservoir containing water. The coefficient of friction between the slots and the gate is $0.03 .$ Determine the minimum vertical force required to lift the gate when the water level is $4 \mathrm{ft}$ above the top edge of the gate.

James Kiss

Numerade Educator

Problem 79

A horizontal 2 -m-diameter conduit is half filled with a liquid $(S G=1.6)$ and is capped at both ends with plane vertical surfaces. The air pressure in the conduit above the liquid surface is 200 kPa. Determine the resultant force of the fluid acting on one of the end caps, and locate this force relative to the bottom of the conduit.

James Kiss

Numerade Educator

Problem 80

Concrete is poured into the forms as shown in Fig. P2.80 to produce a set of steps. Determine the weight of the sandbag needed to keep the bottomless forms from lifting off the ground. The weight of the forms is 85 lb, and the specific weight of the concrete is $150 \mathrm{lb} / \mathrm{ft}^{3}$.

Surendra Kumar

Numerade Educator

Problem 81

Forms used to make a concrete basement wall are shown in Fig. $P 2.81 .$ Each 4 -ft-long form is held together by four ties $-$ two at the top and two at the bottom as indicated. Determine the tension in the upper and lower ties. Assume concrete acts as a fluid with a weight of $150 \mathrm{lb} / \mathrm{ft}^{3}$.

Rashmi Sinha

Numerade Educator

Problem 82

A structure is attached to the ocean floor as shown in Fig. $P 2.82 .$ A 2 -m-diameter hatch is located in an inclined wall and hinged on one edge. Determine the minimum air pressure, $p_{1}$ within the container that will open the hatch. Neglect the weight of the hatch and friction in the hinge.

Surendra Kumar

Numerade Educator

Problem 83

An open rectangular container contains a liquid that has a specific weight that varies according to the equation $\gamma=c_{1}+c_{2} h$ where $c_{1}$ and $c_{2}$ are constants and $h$ is a vertical coordinate measured downward from the free surface. Derive an equation for the magnitude of the liquid force exerted on one wall of the container having a width $b$ and height $H$ and an equation that gives the vertical coordinate of this force.

Mohamed Raafat Mohamed

Mohamed Raafat Mohamed

Numerade Educator

Problem 84

A long, vertical wall separates seawater from fresh water. If the seawater stands at a depth of $7 \mathrm{m},$ what depth of freshwater is required to give a zero resultant force on the wall? When the resultant force is zero, will the moment due to the fluid forces be zero? Explain.

Victor Salazar

Numerade Educator

Problem 85

A gate having the shape shown in Fig. $\mathrm{P} 2.85$ is located in the vertical side of an open tank containing water. The gate is mounted on a horizontal shaft. (a) When the water level is at the top of the gate, determine the magnitude of the fluid force on the rectangular portion of the gate above the shaft and the magnitude of the fluid force on the semicircular portion of the gate below the shaft.
(b) For this same fluid depth determine the moment of the force acting on the semicircular portion of the gate with respect to an axis that coincides with the shaft.

Rashmi Sinha

Numerade Educator

Problem 86

A pump supplies water under pressure to a large tank as shown in Fig. $\mathrm{P} 2.86 .$ The circular-plate valve fitted in the short discharge pipe on the tank pivots about its diameter $A-A$ and is held shut against the water pressure by a latch at $B$. Show that the force on the latch is independent of the supply pressure, $p$, and the height of the tank, $h$.

Rashmi Sinha

Numerade Educator

Problem 87

A homogeneous, 4 -ft-wide, 8 -ft-long rectangular gate weighing 800 lb is held in place by a horizontal flexible cable as shown in Fig. $\mathrm{P} 2.87 .$ Water acts against the gate, which is hinged at point $A .$ Friction in the hinge is negligible. Determine the tension in the cable.

Narayan Hari

Numerade Educator

Problem 88

A rectangular gate 6 ft tall and 5 ft wide in the side of an open tank is held in place by the force $F$ as indicated in Fig. $P .2 .88$ The weight of the gate is negligible, and the hinge at $\mathrm{O}$ is frictionless.
(a) Determine the water depth, $h,$ if the resultant hydrostatic force of the water acts $2.5 \mathrm{ft}$ above the bottom of the gate, i.e., it is collinear with the applied force $F$. (b) For the depth of part (a), determine the magnitude of the resultant hydrostatic force.
(c) Determine the force that the hinge puts on the gate under the above conditions.

James Kiss

Numerade Educator

Problem 89

Sometimes it is difficult to open an exterior door of a building because the air distribution system maintains a pressure difference between the inside and outside of the building. Estimate how big this pressure difference can be if it is "not too difficult" for an average person to open the door.

Narayan Hari

Numerade Educator

Problem 90

An area in the form of an isosceles triangle with a base width of $6 \mathrm{ft}$ and an attitude of $8 \mathrm{ft}$ lies in the plane forming one wall of a tank that contains a liquid having a specific weight of $79.8 \mathrm{lb} / \mathrm{ft}^{3}$. The side slopes upward, making an angle of $60^{\circ}$ with the horizontal. The base of the triangle is horizontal, and the vertex is above the base. Determine the resultant force the fluid exerts on the area when the fluid depth is $20 \mathrm{ft}$ above the base of the triangular area. Show, with the aid of a sketch, where the center of pressure is located.

Arwa Ali

Numerade Educator

Problem 91

Solve Problem 2.90 if the isosceles triangle is replaced with a right triangle having the same base width and altitude as the isosceles triangle.

Allison Knapp

Numerade Educator

Problem 92

A vertical plane area having the shape shown in Fig. $\mathrm{P} 2.92$ is immersed in an oil bath (specific weight $=8.75 \mathrm{kN} / \mathrm{m}^{3}$ ). Determine the magnitude of the resultant force acting on one side of the area as a result of the oil..

Supratim Pal

Numerade Educator

Problem 93

A 3 -m-wide, 8 -m-high rectangular gate is located at the end of a rectangular passage that is connected to a large open tank filled with water as shown in Fig. P2.93. The gate is hinged at its bottom and held closed by a horizontal force, $F_{H},$ located at the center of the gate. The maximum value for $F_{H}$ is $3500 \mathrm{kN}$. (a) Determine the maximum water depth, $h$, above the center of the gate that can exist without the gate opening. (b) Is the answer the same if the gate is hinged at the top? Explain your answer.

Rashmi Sinha

Numerade Educator

Problem 94

Two square gates close two openings in a conduit connected to an open tank of water as shown in Fig. P2.94. When the water depth, $h,$ reaches $5 \mathrm{m}$ it is desired that both gates open at the same time. Determine the weight of the homogeneous horizontal gate and the horizontal force, $R,$ acting on the vertical gate that is required to keep the gates closed until this depth is reached. The weight of the vertical gate is negligible, and both gates are hinged at one end as shown. Friction in the hinges is negligible.

Surendra Kumar

Numerade Educator

Problem 95

A gate having the cross section shown in Fig. 2.95 closes an opening $5 \mathrm{ft}$ wide and $4 \mathrm{ft}$ high in a water reservoir. The gate weighs $500 \mathrm{lb}$, and its center of gravity is $1 \mathrm{ft}$ to the left of $A C$ and 2 ft above $B C$. Determine the horizontal reaction that is developed on the gate at $C$.

Prabhat Tyagi

Numerade Educator

Problem 96

A gate having the cross section shown in Fig. $\mathrm{P} 2.96$ is $4 \mathrm{ft}$ wide and is hinged at $C .$ The gate weighs $18,000 \mathrm{lb}$, and its mass center is $1.67 \mathrm{ft}$ to the right of the plane $B C$. Determine the vertical reaction at $A$ on the gate when the water level is $3 \mathrm{ft}$ above the base. All contact surfaces are smooth.

Prabhat Tyagi

Numerade Educator

Problem 97

The massless, 4 -ft-wide gate shown in Fig. $\mathrm{P} 2.97$ pivots about the frictionless hinge $0 .$ It is held in place by the $2000 \mathrm{lb}$ counterweight, $\% .$ Determine the water depth, $h$.

Surendra Kumar

Numerade Educator

Problem 98

A 200-lb homogeneous gate 10 ft wide and 5 ft long is hinged at point $A$ and held in place by a 12 -ft-long brace as shown in Fig. $\mathrm{P} 2.98 .$ As the bottom of the brace is moved to the right, the water level remains at the top of the gate. The line of action of the force that the brace exerts on the gate is along the brace.
(a) Plot the magnitude of the force exerted on the gate by the brace as a function of the angle of the gate, $\theta$, for $0 \leq \theta \leq 90^{\circ}$. (b) Repeat the calculations for the case in which the weight of the gate is negligible. Common on the result as $\theta \rightarrow 0$.

Surendra Kumar

Numerade Educator

Problem 99

An open tank has a vertical partition and on one side contains gasoline with a density $\rho=700 \mathrm{kg} / \mathrm{m}^{3}$ at a depth of $4 \mathrm{m}$ as shown in Fig. $\mathrm{P} 2.99 .$ A rectangular gate that is $4 \mathrm{m}$ high and $2 \mathrm{m}$ wide and hinged at one end is located in the partition. Water is slowly added to the empty side of the tank. At what depth, $h$ will the gate start to open?

Amit Srivastava

Amit Srivastava

Numerade Educator

Problem 100

A $4-f t$ by $3-f t$ massless rectangular gate is used to close the end of the water tank shown in Fig. $\mathrm{P} 2.100 .$ A $200-1 \mathrm{b}$ weight attached to the arm of the gate at a distance $\ell$ from the frictionless hinge is just sufficient to keep the gate closed when the water depth is $2 \mathrm{ft}$, that is, when the water fills the semicircular lower portion of the tank. If the water were deeper, the gate would open. Determine the distance $\ell$.

James Kiss

Numerade Educator

Problem 101

The rigid gate, $O A B$, of Fig. $\mathrm{P} 2.101$ is hinged at $O$ and rests against a rigid support at $B$. What minimum horizontal force, $P$, is required to hold the gate closed if its width is $3 \mathrm{m} ?$ Neglect the weight of the gate and friction in the hinge. The back of the gate is exposed to the atmosphere.

Victor Salazar

Numerade Educator

Problem 102

A rectangular gate that is $2 \mathrm{m}$ wide is located in the vertical wall of a tank containing water as shown in Fig. P2.102. It is desired to have the gate open automatically when the depth of water above the top of the gate reaches $10 \mathrm{m}$. (a) At what distance,
$d,$ should the frictionless horizontal shaft be located? (b) What is the magnitude of the force on the gate when it opens?

James Kiss

Numerade Educator

Problem 103

A thin 4 -ft-wide, right-angle gate with negligible mass is free to pivot about a frictionless hinge at point $O,$ as shown in Fig. $\mathrm{P} 2.103 .$ The horizontal portion of the gate covers a 1 -ft-diameter drain pipe that contains air at atmospheric pressure. Determine the minimum water depth, $h,$ at which the gate will pivot to allow water to flow into the pipe.

Narayan Hari

Numerade Educator

Problem 104

The inclined face $A D$ of the tank of Fig. $P 2.104$ is a plane surface containing a gate $A B C,$ which is hinged along line $B C .$ The shape of the gate is shown in the plan view. If the tank contains water, determine the magnitude of the force that the water exerts on the gate.

Mayukh Banik

Numerade Educator

Problem 105

An open rectangular tank is $2 \mathrm{m}$ wide and $4 \mathrm{m}$ long. The tank contains water to a depth of $2 \mathrm{m}$ and oil $(S G=0.8)$ on top of the water to a depth of $1 \mathrm{m}$. Determine the magnitude and location of the resultant fluid force acting on one end of the tank.

Khoobchandra Agrawal

Khoobchandra Agrawal

Numerade Educator

Problem 106

An open rectangular settling tank contains a liquid suspension that at a given time has a specific weight that varies approximately with depth according to the following data:
$$\begin{array}{cc}\boldsymbol{h}(\mathbf{m}) & \gamma\left(\mathbf{N} / \mathbf{m}^{3}\right) \\\hline 0 & 10.0 \\
0.4 & 10.1 \\0.8 & 10.2 \\1.2 & 10.6 \\1.6 & 11.3 \\2.0 & 12.3 \\2.4 & 12.7 \\2.8 & 12.9 \\3.2 & 13.0 \\3.6 & 13.1 \\
\hline\end{array}$$
The depth $h=0$ corresponds to the free surface. Determine, by means of numerical integration, the magnitude and location of the resultant force that the liquid suspension exerts on a vertical wall of the tank that is $6 \mathrm{m}$ wide. The depth of fluid in the tank is $3.6 \mathrm{m}$.

AP

Andreas Papavassiliou

Numerade Educator

Problem 107

The closed vessel of Fig. $\mathrm{P} 2.107$ contains water with an air pressure of 10 psi at the water surface. One side of the vessel contains a spout that is closed by a 6 -in.-diameter circular gate that is hinged along one side as illustrated. The horizontal axis of the hinge is located 10 ft below the water surface. Determine the minimum torque that must be applied at the hinge to hold the gate shut. Neglect the weight of the gate and friction at the hinge.

Narayan Hari

Numerade Educator

Problem 108

A 4 -ft-tall, 8 -in. -wide concrete $\left(150 \mathrm{lb} / \mathrm{ft}^{3}\right)$ retaining wall is built as shown in Fig. $\mathrm{P} 2.108$. During a heavy rain, water fills the space between the wall and the earth behind it to a depth $h$ Determine the maximum depth of water possible without the wall tipping over. The wall simply rests on the ground without being anchored to it.

Rashmi Sinha

Numerade Educator

Problem 109

Water backs up behind a concrete dam as shown in Fig. 2.109 Leakage under the foundation gives a pressure distribution under the dam as indicated. If the water depth, $h,$ is too great, the dam will topple over about its toe (point $A$ ). For the dimensions given, determine the maximum water depth for the following widths of the dam, $\ell=20,30,40,50,$ and $60 \mathrm{ft} .$ Base your analysis on a unit length of the dam. The specific weight of the concrete is $150 \mathrm{lb} / \mathrm{ft}^{3}$.

Rashmi Sinha

Numerade Educator

Problem 110

The concrete dam of Fig. P2.1 10 weighs 23.6 $\mathrm{kN} / \mathrm{m}^{3}$ and rests on a solid foundation. Determine the minimum coefficient of friction between the dam and the foundation required to keep the dam from sliding at the water depth shown. Assume no fluid uplift pressure along the base. Base your analysis on a unit length of the dam.

Susan Hallstrom

Susan Hallstrom

Numerade Educator

Problem 111

(See Fluids in the News article titled "The Three Gorges Dam," Section 2.8.) (a) Determine the horizontal hydrostatic force on the 2309 -m-long Three Gorges Dam when the average depth of the water against it is $175 \mathrm{m}$. (b) If all of the 6.4 billion people on Earth were to push horizontally against the Three Gorges Dam, could they generate enough force to hold it in place? Support your answer with appropriate calculations.

James Kiss

Numerade Educator

Problem 112

Obtain a photograph/image of a situation in which the hydrostatic force on a curved surface is important. Print this photo and write a brief paragraph that describes the situation involved.

Surendra Kumar

Numerade Educator

Problem 113

A 2 -ft-diameter hemispherical plexiglass "bubble" is to be used as a special window on the side of an above-ground swimming pool. The window is to be bolted onto the vertical wall of the pool and faces outward, covering a 2 -ft-diameter opening in the wall. The center of the opening is $4 \mathrm{ft}$ below the surface. Determine the horizontal and vertical components of the force of the water on the hemisphere.

Narayan Hari

Numerade Educator

Problem 114

Two round, open tanks containing the same type of fluid rest on a table top as shown in Fig. P2.114. They have the same bottom area, $A$, but different shapes. When the depth, $h$, of the liquid in the two tanks is the same, the pressure force of the liquids on the bottom of the two tanks is the same. However, the force that the table exerts on the two tanks is different because the weight in each of the tanks is different. How do you account for this apparent paradox?

James Kiss

Numerade Educator

Problem 115

Two hemispherical shells are bolted together as shown in Fig. P2.115. The resulting spherical container, which weighs $300 \mathrm{lb}$ is filled with mercury and supported by a cable as shown. The container is vented at the top. If eight bolts are symmetrically located around the circumference, what is the vertical force that each bolt must carry?

Narayan Hari

Numerade Educator

Problem 116

A 4 -m-long curved gate is located in the side of a reservoir containing water as shown in Fig. P2.116. Determine the magnitude of the horizontal and vertical components of the force of the water on the gate. Will this force pass through point $A$ ? Explain.

Supratim Pal

Numerade Educator

Problem 117

The 18 -ft-long lightweight gate of Fig. $P 2.117$ is a quarter circle and is hinged at $H .$ Determine the horizontal force, $P,$ required to hold the gate in place. Neglect friction at the hinge and the weight of the gate.

Surendra Kumar

Numerade Educator

Problem 118

The air pressure in the top of the 2 -liter pop bottle shown in Video $\mathrm{V} 2.6$ and Fig. $\mathrm{P} 2.118$ is $40 \mathrm{psi}$, and the pop depth is 10 in. The bottom of the bottle has an irregular shape with a diameter of 4.3 in. (a) If the bottle cap has a diameter of 1 in. what is the magnitude of the axial force required to hold the cap in place?
(b) Determine the force needed to secure the bottom 2 in. of the bottle to its cylindrical sides. For this calculation assume the effect of the weight of the pop is negligible.
(c) By how much does the weight of the pop increase the pressure 2 in. above the bottom? Assume the pop has the same specific weight as that of water.

Narayan Hari

Numerade Educator

Problem 119

A tank wall has the shape shown in Fig. P2.119. Determine the horizontal and vertical components of the force of the water on a $4-\mathrm{ft}$ length of the curved section $A B$.

Surendra Kumar

Numerade Educator

Problem 120

Hoover Dam (see Video 2.5 ) is the highest arch-gravity type of dam in the United States. A cross section of the dam is shown in Fig. $\mathrm{P} 2.120(a) .$ The walls of the canyon in which the dam is located are sloped, and just upstream of the dam the vertical plane shown in Figure $\mathrm{P} 2.120(b)$ approximately represents the cross section of the water acting on the dam. Use this vertical cross section to estimate the resultant horizontal force of the water on the dam, and show where this force acts.

Rashmi Sinha

Numerade Educator

Problem 121

A plug in the bottom of a pressurized tank is conical in shape, as shown in Fig. P2.121. The air pressure is $40 \mathrm{kPa}$, and the liquid in the tank has a specific weight of $27 \mathrm{kN} / \mathrm{m}^{3} .$ Determine the magnitude, direction, and line of action of the force exerted on the curved surface of the cone within the tank due to the 40 -kPa pressure and the liquid.

Susan Hallstrom

Susan Hallstrom

Numerade Educator

Problem 122

The homogeneous gate shown in Fig. $\mathrm{P} 2.122$ consists of one quarter of a circular cylinder and is used to maintain a water depth of $4 \mathrm{m}$. That is, when the water depth exceeds $4 \mathrm{m}$, the gate opens slightly and lets the water flow under it. Determine the weight of the gate per meter of length.

Amit Srivastava

Amit Srivastava

Numerade Educator

Problem 123

The concrete (specific weight $=150 \mathrm{lb} / \mathrm{ft}^{3}$ ) seawall of Fig. $\mathrm{P} 2.123$ has a curved surface and restrains seawater at a depth of $24 \mathrm{ft}$. The trace of the surface is a parabola as illustrated. Determine the moment of the fluid force (per unit length) with respect to an axis through the toe (point $A$ ).

Amit Srivastava

Amit Srivastava

Numerade Educator

Problem 124

A 12 -in.-diameter pipe contains a gas under a pressure of 140 psi. If the pipe wall thickness is $\frac{1}{4}$ in., what is the average circumferential stress developed in the pipe wall?

Narayan Hari

Numerade Educator

Problem 125

A cylindrical tank with its axis horizontal has a diameter of $2.0 \mathrm{m}$ and a length of $4.0 \mathrm{m}$. The ends of the tank are vertical planes. A vertical 0.1-m-diameter pipe is connected to the top of the tank. The tank and the pipe are filled with ethyl alcohol to a level of $1.5 \mathrm{m}$ above the top of the tank. Determine the resultant force of the alcohol on one end of the tank and show where it acts.

James Kiss

Numerade Educator

Problem 126

Imagine the tank of Problem 2.125 split by a horizontal plane. Determine the magnitude of the resultant force of the alcohol on the bottom half of the tank.

James Kiss

Numerade Educator

Problem 127

If the tank ends in Problem 2.125 are hemispherical, what is the magnitude of the resultant horizontal force of the alcohol on one of the curved ends?

James Kiss

Numerade Educator

Problem 128

An open tank containing water has a bulge in its vertical side that is semicircular in shape as shown in Fig. P2.128. Determine the horizontal and vertical components of the force that the water exerts on the bulge. Base your analysis on a 1 -ft length of the bulge.

Surendra Kumar

Numerade Educator

Problem 129

A closed tank is filled with water and has a $4-\mathrm{ft}$ diameter hemispherical dome as shown in Fig. $2.129 .$ A U-tube manometer is connected to the tank. Determine the vertical force of the water on the dome if the differential manometer reading is $7 \mathrm{ft}$ and the air pressure at the upper end of the manometer is 12.6 psi.

Narayan Hari

Numerade Educator

Problem 130

A 3 -m-diameter open cylindrical tank contains water and has a hemispherical bottom as shown in Fig. P2.130. Determine the magnitude, line of action, and direction of the force of the water on the curved bottom.

Surendra Kumar

Numerade Educator

Problem 131

Three gates of negligible weight are used to hold back water in a channel of width $b$ as shown in Fig. $\mathrm{P} 2.131 .$ The force of the gate against the block for gate $(b)$ is $R$. Determine (in terms of $R$ ) the force against the blocks for the other two gates.

Surendra Kumar

Numerade Educator

Problem 132

Obtain a photograph/image of a situation in which Archimede's principle is important. Print this photo and write a brief paragraph that describes the situation involved.

Surendra Kumar

Numerade Educator

Problem 133

A freshly cut log floats with one fourth of its volume protruding above the water surface. Determine the specific weight of the log.

Rashmi Sinha

Numerade Educator

Problem 134

A $3 \mathrm{ft} \times 3 \mathrm{ft} \times 3 \mathrm{ft}$ wooden cube (specific weight $=37$ $\mathrm{Ib} / \mathrm{ft}^{3}$ ) floats in a tank of water. How much of the cube extends above the water surface? If the tank were pressurized so that the air pressure at the water surface was increased by $1.0 \mathrm{psi} \text { (i.e., } 1 \text { psig })$ how much of the cube would extend above the water surface? Explain how you arrived at your answer.

Prabhu Ramji

Numerade Educator

Problem 135

The homogeneous timber $A B$ of Fig. $\mathrm{P} 2.135$ is $0.15 \mathrm{m}$ by $0.35 \mathrm{m}$ in cross section. Determine the specific weight of the timber and the tension in the rope.

Khoobchandra Agrawal

Khoobchandra Agrawal

Numerade Educator

Problem 136

A river barge, whose cross section is approximately rectangular, carries a load of grain. The barge is 28 ft wide and 90 ft long. When unloaded, its draft (depth of submergence) is $5 \mathrm{ft}$ and with the load of grain the draft is $7 \mathrm{ft}$. Determine:
(a) the unloaded weight of the barge, and
(b) the weight of the grain.

Narayan Hari

Numerade Educator

Problem 137

A tank of cross-sectional area $A$ is filled with a liquid of specific weight $\gamma_{1}$ as shown in Fig. $\mathrm{P} 2.137 a .$ Show that when a cylinder of specific weight $\gamma_{2}$ and volume $\psi$ is floated in the liquid (see Fig. $\mathrm{P} 2.137 b$ ), the liquid level rises by an amount $\Delta h=$ $\left(\gamma_{2} / \gamma_{1}\right) \forall / A$.

Surendra Kumar

Numerade Educator

Problem 138

When the Tucurui Dam was constructed in northern Brazil, the lake that was created covered a large forest of valuable hardwood trees. It was found that even after 15 years underwater the trees were perfectly preserved and underwater logging was started. During the logging process a tree is selected, trimmed, and anchored with ropes to prevent it from shooting to the surface like a missile when cut. Assume that a typical large tree can be approximated as a truncated cone with a base diameter of $8 \mathrm{ft},$ a top diameter of $2 \mathrm{ft}$, and a height of $100 \mathrm{ft}$. Determine the resultant vertical force that the ropes must resist when the completely sinkmerged tree is cut. The specific gravity of the wood is approximately 0.6.

Surendra Kumar

Numerade Educator

Problem 139

Estimate the minimum water depth needed to float a canoe carrying two people and their camping gear. List all assumptions and show all calculations.

Surendra Kumar

Numerade Educator

Problem 140

An inverted test tube partially filled with air floats in a plastic water-filled soft drink bottle as shown in Video $\mathrm{V} 2.7$ and Fig. $\mathrm{P} 2.140 .$ The amount of air in the tube has been adjusted so that it just floats. The bottle cap is securely fastened. A slight squeezing of the plastic bottle will cause the test tube to sink to the bottom of the bottle. Explain this phenomenon.

Surendra Kumar

Numerade Educator

Problem 141

An irregularly shaped piece of a solid material weighs 8.05 Ib in air and 5.26 lb when completely submerged in water. Determine the density of the material.

Narayan Hari

Numerade Educator

Problem 142

A 1 -ft-diameter, 2 -ft-long cylinder floats in an open tank containing a liquid having a specific weight $\gamma$. A U-tube manometer is connected to the tank as shown in Fig. P2.142. When the pressure in pipe $A$ is 0.1 psi below atmospheric pressure, the various fluid levels are as shown. Determine the weight of the cylinder. Note that the top of the cylinder is flush with the fluid surface.

Surendra Kumar

Numerade Educator

Problem 143

A 1 -m-diameter cylindrical mass, $M,$ is connected to a $2-\mathrm{m}-$ wide rectangular gate as shown in Fig. $\mathrm{P} 2.143 .$ The gate is to open when the water level, $h$, drops below $2.5 \mathrm{m}$. Determine the required value for $M$. Neglect friction at the gate hinge and the pulley.

Surendra Kumar

Numerade Educator

Problem 144

The thin-walled, 1-m-diameter tank of Fig. P2.144 is closed at one end and has a mass of $90 \mathrm{kg}$. The open end of the tank is lowered into the water and held in the position shown by a steel block having a density of $7840 \mathrm{kg} / \mathrm{m}^{3}$. Assume that the air that is trapped in the tank is compressed at a constant temperature. Determine:
(a) the reading on the pressure gage at the top of the tank, and
(b) the volume of the steel block.

Keshav Singh

Numerade Educator

Problem 145

When a hydrometer (see Fig. P2.145 and Video V2.8 ) having a stem diameter of 0.30 in. is placed in water, the stem protrudes 3.15 in. above the water surface. If the water is replaced with a liquid having a specific gravity of $1.10,$ how much of the stem would protrude above the liquid surface? The hydrometer weighs $0.042 \mathrm{lb}$.

Surendra Kumar

Numerade Educator

Problem 146

A 2 -ft-thick block constructed of wood $(S G=0.6)$ is submerged in oil $(S G=0.8)$ and has a 2 -ft-thick aluminum (specific weight $=168 \mathrm{lb} / \mathrm{ft}^{3}$ ) plate attached to the bottom as indicated in Fig. $\mathrm{P} 2.146 .$ Determine completely the force required to hold the block in the position shown. Locate the force with respect to point $A$.

Surendra Kumar

Numerade Educator

Problem 147

(See Fluids in the News article titled "Concrete canoes," Section 2.11.1. crete canoe displace compared to an ultralightweight 38 -lb Kevlar canoe of the same size carrying the same load?

Surendra Kumar

Numerade Educator

Problem 148

An iceberg (specific gravity 0.917 ) floats in the ocean (specific gravity 1.025 ). What percent of the volume of the iceberg is under water?

Ajay Singhal

Numerade Educator

Problem 149

Obtain a photograph/image of a situation in which the pressure variation in a fluid with rigid-body motion is involved. Print this photo and write a brief paragraph that describes the situation involved.

Surendra Kumar

Numerade Educator

Problem 150

It is noted that while stopping, the water surface in a glass of water sitting in the cup holder of a car is slanted at an angle of $15^{\circ}$ relative to the horizontal street. Determine the rate at which the car is decelerating.

Supratim Pal

Numerade Educator

Problem 151

An open container of oil rests on the flatbed of a truck that is traveling along a horizontal road at $55 \mathrm{mi} / \mathrm{hr}$. As the truck slows uniformly to a complete stop in $5 \mathrm{s}$, what will be the slope of the oil surface during the period of constant deceleration?

Surendra Kumar

Numerade Educator

Problem 152

A 5 -gal, cylindrical open container with a bottom area of 120 in. $^{2}$ is filled with glycerin and rests on the floor of an ele-
vator.
(a) Determine the fluid pressure at the bottom of the container when the elevator has an upward acceleration of $3 \mathrm{ft} / \mathrm{s}^{2}$
(b) What resultant force does the container exert on the floor of the elevator during this acceleration? The weight of the container is negligible. (Note: 1 gal $=231$ in. $^{3}$ ).

James Kiss

Numerade Educator

Problem 153

An open rectangular tank $1 \mathrm{m}$ wide and $2 \mathrm{m}$ long contains gasoline to a depth of $1 \mathrm{m}$. If the height of the tank sides is $1.5 \mathrm{m}$ what is the maximum horizontal acceleration (along the long axis of the tank) that can develop before the gasoline would begin to spill?

Supratim Pal

Numerade Educator

Problem 154

If the tank of Problem 2.153 slides down a frictionless plane that is inclined at $30^{\circ}$ with the horizontal, determine the angle the free surface makes with the horizontal.

Chai Santi

Numerade Educator

Problem 155

A closed cylindrical tank that is $8 \mathrm{ft}$ in diameter and $24 \mathrm{ft}$ long is completely filled with gasoline. The tank, with its long axis horizontal, is pulled by a truck along a horizontal surface. Determine the pressure difference between the ends (along the long axis of the tank) when the truck undergoes an acceleration of $5 \mathrm{ft} / \mathrm{s}^{2}$.

James Kiss

Numerade Educator

Problem 156

The open U-tube of Fig. $\mathrm{P} 2.156$ is partially filled with a liquid. When this device is accelerated with a horizontal acceleration
$a,$ a differential reading $h$ develops between the manometer legs which are spaced a distance $\ell$ apart. Determine the relationship between $a, \ell,$ and $h$.

Hast Aggarwal

Numerade Educator

Problem 157

The U-tube of Fig. $\mathrm{P} 2.157$ is partially filled with water and rotates around the axis $a-a$. Determine the angular velocity that will cause the water to start to vaporize at the bottom of the tube $(\text { point } A)$.

Satpal Satpal

Numerade Educator

Problem 158

The U-tube of Fig. $\mathrm{P} 2.158$ contains mercury and rotates about the off-center axis $a-a$. At rest, the depth of mercury in each leg is $150 \mathrm{mm}$ as illustrated. Determine the angular velocity for which the difference in heights between the two legs is $75 \mathrm{mm}$.

Tarandeep Singh

Tarandeep Singh

Numerade Educator

Problem 159

An open 1 -m-diameter tank contains water at a depth of $0.7 \mathrm{m}$ when at rest. As the tank is rotated about its vertical axis the center of the fluid surface is depressed. At what angular velocity will the bottom of the tank first be exposed? No water is spilled from the tank.

James Kiss

Numerade Educator

Problem 160

An open, 2 -ft-diameter tank contains water to a depth of $3 \mathrm{ft}$ when at rest. If the tank is rotated about its vertical axis with an angular velocity of 180 rev/min, what is the minimum height of the tank walls to prevent water from spilling over the sides?

Narayan Hari

Numerade Educator

Problem 161

A child riding in a car holds a string attached to a floating, helium-filled balloon. As the car decelerates to a stop, the balloon tilts backwards. As the car makes a right-hand turn, the balloon tilts to the right. On the other hand, the child tends to be forced forward as the car decelerates and to the left as the car makes a righthand turn. Explain these observed effects on the balloon and child.

James Kiss

Numerade Educator

Problem 162

A closed, 0.4 -m-diameter cylindrical tank is completely filled with oil $(S G=0.9)$ and rotates about its vertical longitudinal axis with an angular velocity of $40 \mathrm{rad} / \mathrm{s}$. Determine the difference in pressure just under the vessel cover between a point on the circumference and a point on the axis.

Amit Srivastava

Amit Srivastava

Numerade Educator

Problem 163

(See Fluids in the News article titled "Rotating mercury mirror telescope," Section $2.12 .2 .$ ) The largest liquid mirror telescope uses a 6 -ft-diameter tank of mercury rotating at 7 rpm to produce its parabolic-shaped mirror as shown in Fig. P2.163. Determine the difference in elevation of the mercury, $\Delta h,$ between the edge and the center of the mirror.

James Kiss

Numerade Educator