Numerade

Questions asked

BEST MATCH

A quality control want to estimate the portion of defective components that are being manufactured by his company tovwithin2.5% a sample of 300 components showed that 20 were defective how large a sample size is needed to estimate the true porportionof the defective components with 99% confidence

View Answer

BEST MATCH

Consider the following IEEE 754 32-bit floating point value: 01001111 01001000 00000000 00000000 Enter S, its sign, as either + or -. Enter E, its exponent part's value, in base 10 (not including the -127 bias). Enter F, its fraction part's value, in base 10 in the form 0.XXXX where X is a digit.

View Answer

BEST MATCH

A charge $q_1 = + 5.0 \, nC$ is placed at the origin of the XY-coordinate system, and a charge $q_2 = -2.0 \, nC$ is placed on the positive x-axis at $x = 4.0 \, cm$. If a third charge $q_3 = + 6.0 \, nC$ is now placed at the point at $x = 4.0 \, cm$ and $y = 3.0 \, cm$, find the force excerpt by $q_2$ on $q_3$ $1.198 \times 10^{-4} N$ $8.63 \times 10^{-5} N$ $1.079 \times 10^{-4} N$ $1.023 \times 10^{-4} N$ $6.48 \times 10^{-5} N$

View Answer

BEST MATCH

What would be the best type of microscope to use to view the following specimen? Malaria in a red blood cell Compound scope Dissecting scope No scope needed, cells are visible with the naked eye

View Answer

BEST MATCH

Because offset section views cut oddly through an object, it is common practice to include hidden lines in them. A rib or web is a narrow, flat part that provides support to an object. Legos fit together because they have a locational fit. A countersunk hole is one that has a larger diameter hole drilled deep enough to provide a volume for the head of a screw to be hidden. A key is a threaded fastener. Auxiliary views are primarily used to reduce the number of hidden lines in a drawing. A transition fit may have interference. A detail drawing contains information about material. A broken-out section view only reveals part of the internal features of an object and is not indicated on another view by a cutting plane line. Lay refers to the basic orientation of the part for assembling. An LC fit may have clearance. Solidworks is a solid modeling programs because you draw parts much like you'd create them on a sheet of paper. "Hardware" commonly refers to metal materials that are harder than plastics. The following three questions refer to the figure to the right. This symbol indicates that material must be removed. This symbol indicates that the lay of the machining must be parallel to the line representing the surface. This symbol indicates that the material must have a hardness of at least 63 µin. 63 =

View Answer

BEST MATCH

A Gap call option is a European call option which at maturity T pays off S(T) − X1 when S(T) > X2, or nothing when S(T) ≤ X2. Here X1 is known as the strike price and X2 is the trigger price.

View Answer

BEST MATCH

Question 3 One of these four answers represents government economic policies that would be corroborated by neoclassical macroeconomic analysis. Which one? focus on long-term growth and on controlling inflation focus on combating depression and cyclical unemployment focus on real GDP and cyclical unemployment focus on short-term recession and controlling inflation 1 pts

View Answer

BEST MATCH

Rocky Mountain spotted fever ________. Group of answer choices is transmitted by Ixodes ticks never has severe complications symptoms include fever, headache, and rash is seen in highest numbers along the west coast All of the choices are correct.

View Answer

BEST MATCH

5. Determine the critical points of f(x) = x - 2cosx for the interval [-π, π]

View Answer

BEST MATCH

if the nominal interst rate is 18 percent and the real interest rate is 6 percent, the inflation rate is

View Answer

christopher s.