Numerade

Questions asked

BEST MATCH

Which one of the following is determined from exercise tests that rely on both the phosphagen system (ATP-PC) and glycolysis as the primary energy systems? anaerobic power anaerobic capacity power endurance aerobic power

View Answer

BEST MATCH

Most companies require long-term capital to purchase fixed assets such as plant and equipment, to develop new products and services, or to finance an expansion. Group startsTrue or False True, unselectedFalse, unselected

View Answer

BEST MATCH

A large firm that is highly interconnected with others can be a source of \_\_\_\_\_\_\_\_ which is the possibility that an event at the firm could trigger severe instability in financial markets or the collapse of an entire industry or economy. tipper risk systemic means systemic risk systemic offerings

View Answer

BEST MATCH

The colorblind approach to diversity Group of answer choices has been broken down into four varieties (based on awareness of racial inequality (high/low) and prejudice (high/low)) in work by researchers including Dr. Mazzocco argues for ignoring and/or eliminating racial categories All of these is not recommended by researchers

View Answer

BEST MATCH

During the energy generation phase of anaerobic glycolysis of a glucose molecule , what is the net gain of ATP? more than 4

View Answer

BEST MATCH

Angela Company uses both standards and budgets. For the year, estimated production of Product X is 507,000 units. Total estimated cost for materials and labor are $1,419,600 and $1,774,500 respectively. Compute the estimates for (a) a standard cost and (b) a budgeted cost. (Round standard costs to 2 decimal places, e.g. 1.25.)

View Answer

BEST MATCH

(a) Molarity of a solution prepared by diluting 33.42 mL of 0.269 M potassium chloride to 150.00 mL (b) Molarity of a solution prepared by diluting 25.15 mL of 0.0706 M ammonium sulfate to 500.00 mL (c) Molarity of sodium ion in a solution made by mixing 4.09 mL of 0.289 M sodium chloride with 500. mL of 6.51 x 10^-3 M sodium sulfate (assume volumes are additive) How many grams of NaH2PO4 are needed to react with 31.90 mL of 0.265 M NaOH? NaH2PO4(s) + 2 NaOH(aq) → Na3PO4(aq) + 2 H2O(l) How many moles of excess reactant (H2SO4) are present when 363.0 mL of 0.227 M sulfuric acid reacts with 0.510 L of 0.154 M sodium hydroxide to form water and aqueous sodium sulfate? If 26.18 mL of 0.1750 M NaOH solution is required to neutralize 43.17 mL of H2SO4, what is the molarity of the acid solution? Sodium hydroxide is used extensively in acid-base titrations because it is a strong, inexpensive base. A sodium hydroxide solution was standardized by titrating 20.67 mL of 0.1528 M standard hydrochloric acid. The initial buret reading of the sodium hydroxide was 2.30 mL, and the final reading was 38.76 mL. What was the molarity of the base solution?

View Answer

BEST MATCH

(iii) Use the method of variation of parameters to find the general solution of the differential equation $3x^2 \frac{d^2y}{dx^2} - 6x \frac{dy}{dx} + 6y = \frac{1}{x^4}$ $(x > 0)$.

View Answer

BEST MATCH

I don't know Question number 7 What is the probability that a single card drawn from a standard deck of cards is either an 8 or a heart? (Enter your answer as a simplified fraction. )

View Answer

BEST MATCH

QUESTION 2: A three-phase star-connected source feeds two balanced three-phase loads. The first load is 560.1 kVA with a power factor of 0.707 and the second load is 132 kW with a power factor of 1. The impedance of the transmission line between the source and the load is given as 0.4+j2.7 Î© in phase. Since the interphase voltage at the load terminals is 3810.5 Volts; a) Determine the line voltage of the source. b) Calculate the values of active and reactive power consumed on the transmission line between the source and the load. c) Calculate the values of active and reactive power drawn from the source. 1) Calculate the line voltage of the source and enter it in the box below. (Two digits after the comma will be taken.) 2) Calculate the active power value spent on the transmission line between the source and the load and enter it in the box below. (Two digits after the comma to be entered in kilowatt will be taken.) 3) Calculate the reactive power value spent on the transmission line between the source and the load and enter it in the box below. (Kilovoltampereactive (kVAR) will be entered in kilovoltampereactive (two digits after the comma will be taken). 4) Calculate the value of active power drawn from the source. (The value will be entered in kilowatt and two digits will be taken after the comma.) 5) Calculate the reactive power value drawn from the source and enter it in the box below. (Two digits after the comma to be entered in kilovoltampereactive (kVAR) will be taken.)

View Answer

patricia d.