Numerade

Questions asked

BEST MATCH

QUESTION 2 (30 points): $$G(s) = \frac{s + 25}{(0.004s + 1)(0.5s + 25)}$$ By using the system transfer function, G(s), given in above a) Sketch the approximate Bode Plot (both magnitude and phase) of the frequency response using first order asymptotic approximations. Show your steps clearly. (15pts) b) What is the bandwidth and the resonant peak value of the frequency response of this system based on your approximation from part (a)? (5pts) c) Assume that $$G(s) = Y(s)/V(s)$$ represents the transfer function of an electromechanical system where $$V(s)$$ is a voltage input. Designers decide to improve the response properties of this system by attaching an voltage amplifier to its input port (i.e., $$V(s)= K * V_{amp}(s))$$ where voltage gain K is adjustable. Find the value of K in this new system with the amplifier (i.e., $$G_{new}(s) = Y(s)/V_{amp}(s))$$ such that the new resonant peak value is half of the value from part (b)? (10pts)

View Answer

BEST MATCH

Problem 3 [24 pts] Show all relevant work!!! Three ideal batteries and three resistors are connected as shown in the figure. The resistor values are $R_1 = 4.0 \ \Omega$, $R_2 = 8.0 \ \Omega$, and the batteries have $E_1 = 6.0 \ V$, $E_2 = 12.0 \ V$. a) [3 pts] Use the junction rule in node a or b to write the junction equation for currents $i_1$, $i_2$ and $i_3$ b) [10 pts] Write two loop equations for the left and right loops of the circuit. c) [5 pts] Current $i_2 = 0.25 \ A$. Find the magnitude and direction of currents $i_1$ and $i_3$. Do the directions match those in the figure? d) [6 pts] At what rate is energy dissipated in resistor $R_2$?

View Answer

BEST MATCH

What separates the elite or world class swimmers from each other on the startingblock? Power/Speed Training they underwent Mental strength B & C

View Answer

BEST MATCH

There is a maximum depth increases, so does the pressure difference, which tends to collapse the diver's lungs. Since the snorkel connects the air in the lungs to the atmosphere at the surface

View Answer

BEST MATCH

ln(x) + ln(x - 7) = 0 x = 7.464

View Answer

BEST MATCH

$ 1 0 \longdiv { 3 8 } $

View Answer

BEST MATCH

If you invest $1,000 into a savings account at an interest rate of 4%, compounded annually, how much will you have in the savings account after 8 years?

View Answer

BEST MATCH

Required: Designing a complete continuous network that somewhat simulates reality using the packet tracer program. All protocols covered within the laboratory. The conditions: - The network must be fully connected to each other with full connectivity. - The network must contain (at least 2 routers of any kind). - The network must contain, as a minimum, all of the following protocols: DNS, HTTP, DHCP, telnet. - One routing protocol (static, RIP, OSPF, etc.). - The use of various network and IP numbers of all categories, as well as the use of addresses that have been made for them subnetting (classless IP address). - Allocating a part of the network for the work of VLAN & InterVLAN Routing Protocol as a minimum 1 VLAN.

View Answer

BEST MATCH

5) Find the distance from the point to the given plane. (3, -2, 7), 4x - 6y + z = 5 6) Reparametrize the curve with respect to arc length measured from the point where t = 0 in the direction of increasing t. r(t) = (e^t cos(2t), 2, e^t sin(2t)) 7) For r(t) = (t^2, 2t, ln(t)) a) Find the unit tangent and unit normal vectors T(t) and N(t) b) Find the curvature. Please explain the solution in detail step by step format as I need help understanding the concepts.

View Answer

BEST MATCH

1. Match: Determine whether each of the following is classified as a. Direct Materials b. Direct labor c. Manufacturing overhead. Write the appropriate letter in the space provided. A. Factory machinery lubricants B. Depreciation on manufacturing building C. Wood used in manufacturing furniture D. Assembly line worker's wages E. Salaries for the night security guards for the factory building F. Glue, nails and other small parts used in production G. Insurance on factory machines H. Factory supervisor's salaries I. Metal used in manufacturing process J. Heat and electricity for factory A. Manufacturing overhead B. Manufacturing overhead C. Direct Materials D. Manufacturing overhead E. Manufacturing overhead F. Direct Materials G. Manufacturing overhead H. Direct labor I. Manufacturing overhead J. Manufacturing overhead QUESTION 2 Match: For each item, identify if it should be classified as: a. Product Cost b. Period Cost Write the appropriate letter in the space provided. A. Office supplies used B. Sales commissions paid to sales' personnel C. Production superintendent's salaries D. Property taxes on factory building E. Depreciation on delivery trucks F. Factory repairs G. Supplies used in the administrative offices H. Factory manager's salary I. Delivery equipment repairs J. Advertising A. Period Cost B. Product Cost C. Period Cost D. Period Cost E. Period Cost F. Product Cost G. Product Cost H. Period Cost I. Product Cost J. Period Cost

View Answer

yvonne s.