00:01
All right, let's start by looking at your data.
00:04
So we have class limits and frequency.
00:12
And i've placed this on grid paper for the sake of you're going to have to draw some graphs.
00:21
All right, so our first class is from 1 through 25, and there are 16 pieces of data in that class.
00:30
And then we have 26 through 50, and there are 14 pieces of data there.
00:37
There's 51 to 75, and there's nine pieces of data.
00:45
Then we have 76 up to 100, holds five pieces of data.
00:51
From 101 to 125, there are no pieces of data.
00:57
From 126 up to 150, there is one piece of data.
01:03
From 151 to 175, there's also a piece of data.
01:08
One piece of data from 176 up to 200 there's none from 201 to 225 there are none from 226 up to 250 there is one and from 251 up to 275 there is no data and the grand total on that is 56 and this data represented the 56 counties in pennsylvania, as well as the number of bears that were killed in each of those counties.
01:51
So the first thing you needed to do was to draw a histogram.
01:55
Now, in order to draw a histogram, you're going to have to talk in terms of class boundaries, not just class limits.
02:03
So we're going to extend our chart a little bit, and we're going to talk about class boundaries.
02:17
And with the class boundaries, what you're going to do is you're going to back up the lower class limits, which would be the numbers right here.
02:30
All of these numbers, we're going to back them up by a half.
02:34
So we're going to start at 0 .5, and then we'll start at 25 .5, and then we'll start at 5, and then we'll start at 5 .5, 50 .5 and 75 .5, 100 .5, 120 .5.
02:55
150 .5.
02:55
150 .5.
02:58
175 .75 .75.
03:00
I think i kind of shifted a little bit.
03:03
I think i kind of shifted a little bit.
03:07
So 200 .5 to 25 .5.
03:13
And 250 .5.
03:16
And then we're going to take all the upper class limits and we're going to raise them by a half.
03:24
So that means this one's going to end at 25 .5, 50 .5, 75 .5, 100 .5, 125 .5, 150 .5.
03:44
175, .5, 200 .5, 225.
03:57
250.
03:58
And 275.
04:03
Now the reason we did that was when we draw histograms, our towers are supposed to touch.
04:10
So the way they were over in the class limits section, if we had a number like 25, there would be no class that it would fall in.
04:21
So by backing up the lower class limits and increasing the upper class limits we now have homes for numbers in between all of the integers and it will also guarantee that our towers in the histogram end up budding up against each other.
04:41
So now let's do the first histogram.
04:45
So i'm going to just screwed up a little bit and we're going to set up our axes.
04:51
So again, by having the nice grid system, it works out well.
04:56
So the first thing we're going to do is we're going to draw our vertical axis and we're going to let this be two, four, six, eight, ten, twelve, fourteen, and 16.
05:12
We're going to draw our horizontal axis and we're going to use the class boundaries as our numbering on the axis.
05:26
So the first line is going to be 0 .5 and then 25 .5 and 50 .5, 75 .5, 100.
05:49
125 .5, 150 .5, and 175 .75.
05:57
.
05:57
.
05:57
200.
06:01
.225.
06:04
25.
06:06
.5 and to 75.
06:09
.5.
06:11
And then the next thing we're going to do is we're going to look at our chart, and we're going to construct our histogram towers.
06:19
So for the class boundaries of 0 .5 to 25 .5, we had 16 bears that were killed.
06:30
So therefore, we are going to construct a tower that spans from 0 .5, goes to a height of 16, and over to 25 .5.
06:47
And then as we go back up here to span from 25 .5 up to 50 .5, there were 14 bears that were killed.
07:07
So 25 .5 up to 14 and back to the 50 .5.
07:19
And let's go back and look.
07:21
Then for the next set of class boundaries, we had nine bears.
07:36
So we're going to go up to nine and back down.
07:46
And then for the next, we had five.
07:52
So we'll go up to five and over and down.
08:03
And then the next, we had none.
08:07
And then we had one from 125 .5 to...
08:17
So we'll go here.
08:22
And then we had another one with one.
08:32
And then we had two more categories with none.
08:36
And then from 225 to 250 .5, we had two.
08:50
So that would be our histogram.
08:53
And if you really wanted to, you can kind of color them in, kind of make them stand out a little bit.
09:24
So that would be your histogram.
09:27
Now, you should also label your axes.
09:31
So across the bottom, we are talking about the number of bears killed.
09:45
And actually, the number of bears killed would be up the side.
09:51
It's the frequency.
09:58
And up the side would be the number of counties.
10:11
Okay, so we're ready now to do our frequency polygon.
10:16
Now our frequency polygon is going to be basically set up the same way, but instead of using our class boundaries, we're going to have to talk about midpoints...